Digital Man wrote to Otto Reverse <=-

Some Synchronet BBSes have *other* X/Y/ZMODEM protocol drivers
available for users too (e.g. cvs.synchro.net has lsz/rz available for use). Give that a try and see if you get different results. --
digital man

Thanks, lsz on Vertrauen worked fine. 1.8mb QWK packet transferred
over 19,200 baud (yup, need to buy a UART 16550 card lol) taking
16 minutes without a single CRC error.

What switches for sz are you using if any on Vertrauen? I ask
because I have a Linux box with telnet and lrzsz on my LAN that
I cannot use sz with successfully (to this Simulant Retro Wifi
gizmo). I have to resort to Kermit which never has any errors
but of course is slow.

On the other hand I suppose perhaps the telnet server setup on
my Linux box might need something configured differently rather
than sz.

Cheers,
Doug


... Living on the edge...the trailing edge that is!
--- MultiMail/DOS v0.52
þ Synchronet þ Vertrauen þ Home of Synchronet þ [vert/cvs/bbs].synchro.net

Re: SEXYZ, DOS, Modem Emulato
By: Otto Reverse to Digital Man on Fri May 07 2021 09:54 am

What switches for sz are you using if any on Vertrauen?

For ZMODEM send, it's just 'sz %f' for single-file and 'sz %s' for batch.
--
digital man

This Is Spinal Tap quote #29:
I find lost luggage. I locate mandolin strings in the middle of Austin!
Norco, CA WX: 67.1øF, 67.0% humidity, 1 mph NW wind, 0.00 inches rain/24hrs
---
þ Synchronet þ Vertrauen þ Home of Synchronet þ [vert/cvs/bbs].synchro.net

Re: SEXYZ, DOS, Modem Emulators
By: Digital Man to Otto Reverse on Thu May 06 2021 12:07 pm

Some Synchronet BBSes have *other* X/Y/ZMODEM protocol drivers available for users too (e.g. cvs.synchro.net has lsz/rz available for use). Give that a try and see if you get different results.

Well that worked. In Procom Plus and Telemate I can use SZ with no hiccups. I was able to download a 1.8mb QWK packet with zero errors.

I wasn't able to upload using a variety of modes in PC Plus. Was able to upload in kermit in Telemate at 9600 baud (my old 486 only has 8250 UART chips). But I see that even though the upload appeared to complete that my packet wasn't processed. The other modes I tried the file would transfer but the transfer process would never end. It was like my software wasn't telling the BBS that the transfer was done. Kept endlessly retrying to send the last packet (regardless of mode I tried).

I have an ISA 16C650 chip based serial card coming in the mail so that might help. Painful to buy though. Cheapest I could find when factoring in shipping. It was only $20 and is new old stock. But shipping (US to Canada) was $25!

Anyway, progress has been made and we'll see how things fair with the new serial card once it comes.

Cheers,
Doug

PS I like this new (to me) FSEditor!

---
þ Synchronet þ Vertrauen þ Home of Synchronet þ [vert/cvs/bbs].synchro.net

Digital Man wrote to Otto Reverse <=-

For ZMODEM send, it's just 'sz %f' for single-file and 'sz %s' for
batch. --
digital man

Okay. So my issue is likely the telnet server config.

Can I ask what area my reply has ended up? When listing Synchronet
Discussion while logged into the BBS (after I uploaded my REP packet
of course) I did not see my reply so I assumed the REP packet did not
get processed (wasn't watching closely during the upload). But my
reply obviously got to you of course.

In MultiMail I just typed R for reply, chose the already highlighted Synchronet (which I assume is the short name for the DOVE-Net echo
Synchronet Discussion) and then chose NO to "make this private".

So I would assume that after my REP packet is uploaded and processed
that I should be able to list the Synchronet Discussion echo and see
my reply there?

Lot's of cobwebs to brush off on my part lol.

Cheers,
Doug

... Living on the edge...the trailing edge that is!
--- MultiMail/DOS v0.52
þ Synchronet þ Vertrauen þ Home of Synchronet þ [vert/cvs/bbs].synchro.net

Re: SEXYZ, DOS, Modem Emulato
By: Otto Reverse to Digital Man on Fri May 07 2021 02:52 pm

Digital Man wrote to Otto Reverse <=-

For ZMODEM send, it's just 'sz %f' for single-file and 'sz %s' for batch. --
digital man

Okay. So my issue is likely the telnet server config.

Can I ask what area my reply has ended up?

DOVE-Net Synchronet Discussion

When listing Synchronet
Discussion while logged into the BBS (after I uploaded my REP packet
of course) I did not see my reply so I assumed the REP packet did not
get processed (wasn't watching closely during the upload). But my
reply obviously got to you of course.

In MultiMail I just typed R for reply, chose the already highlighted Synchronet (which I assume is the short name for the DOVE-Net echo Synchronet Discussion) and then chose NO to "make this private".

So I would assume that after my REP packet is uploaded and processed
that I should be able to list the Synchronet Discussion echo and see
my reply there?

Yes. There are about 4000 messages in the base right now, so one message might be easy to over look.
--
digital man

Rush quote #35:
Static on your frequency, electrical storm in your veins
Norco, CA WX: 69.2øF, 60.0% humidity, 18 mph NE wind, 0.00 inches rain/24hrs ---
þ Synchronet þ Vertrauen þ Home of Synchronet þ [vert/cvs/bbs].synchro.net