Anyone having an issue with Fluke cases getting brittle? I have a 177 that had the battery cover crack in the screw boss area, and the other side won't hold a screw as the inside post is cracked. The plastic is brittle and reminds me of the aging of
plastic in 1990s plastic television cabinets. My 85s never did this and I have a very old 77 that is still in perfect shape although it doesn't get a of use. The 177 is my daily meter and yes, it's fallen a few times.

--- SoupGate-Win32 v1.05
* Origin: fsxNet Usenet Gateway (21:1/5)

On Tuesday, January 25, 2022 at 11:29:45 AM UTC-5, ohg...@gmail.com wrote:

Anyone having an issue with Fluke cases getting brittle? I have a 177 that had the battery cover crack in the screw boss area, and the other side won't hold a screw as the inside post is cracked. The plastic is brittle and reminds me of the aging of

plastic in 1990s plastic television cabinets. My 85s never did this and I have a very old 77 that is still in perfect shape although it doesn't get a of use. The 177 is my daily meter and yes, it's fallen a few times.


Sorry to hear.
I have 3 fluke multimeters: a 77(30 yo?), 179 (6-7 yo?), and 289 (~2 yo). None of them have the issues you describe. The 179 is my daily driver most of the time.
Surprising that the aging plastic issue would crop up on a Fluke.
For the inside post repair, you may want to consider, if there is enough space, to slide over a plastic sleeve filled with epoxy to reinforce it? Then use a slightly oversized screw?
Heat-shrink sleeve over post perhaps?
good luck
J

--- SoupGate-Win32 v1.05
* Origin: fsxNet Usenet Gateway (21:1/5)

ohg...@gmail.com wrote:
====================

Anyone having an issue with Fluke cases getting brittle?

** Yep.

I have a 177 that had the battery cover crack in the screw boss area,
and the other side won't hold a screw as the inside post is cracked.

** All the posts for the back screws on my 70 series 2 have failed.
Plus the "clicker" on the ranges switch broke about 10 year back.

Bought the meter in about '95 - it failed completely 2 years ago.
Not a common problem with other DMMs I own,


..... Phil

--- SoupGate-Win32 v1.05
* Origin: fsxNet Usenet Gateway (21:1/5)

On Tuesday, January 25, 2022 at 12:15:06 PM UTC-5, Three Jeeps wrote:

On Tuesday, January 25, 2022 at 11:29:45 AM UTC-5, ohg...@gmail.com wrote:

Anyone having an issue with Fluke cases getting brittle? I have a 177 that had the battery cover crack in the screw boss area, and the other side won't hold a screw as the inside post is cracked. The plastic is brittle and reminds me of the aging of

plastic in 1990s plastic television cabinets. My 85s never did this and I have a very old 77 that is still in perfect shape although it doesn't get a of use. The 177 is my daily meter and yes, it's fallen a few times.

Sorry to hear.
I have 3 fluke multimeters: a 77(30 yo?), 179 (6-7 yo?), and 289 (~2 yo). None of them have the issues you describe. The 179 is my daily driver most of the time.
Surprising that the aging plastic issue would crop up on a Fluke.
For the inside post repair, you may want to consider, if there is enough space, to slide over a plastic sleeve filled with epoxy to reinforce it? Then use a slightly oversized screw?
Heat-shrink sleeve over post perhaps?
good luck
J

I'm sure I could kluge up a fix (or just retire the meter - it's close to 10 years IIRC), but I was more curious if anyone else had seen this (yet?) The brittle plastic syndrome was bizarre and I'm wondering if I'm an early victim of this on Fluke
meters. Years ago, I remember two guys bringing in a 32" Sony flat CRT TV for repair and heard the telltale snapping as they muscled the beast in the door. It literally came apart in their hands and the CRT fell out the front as they put it down.

--- SoupGate-Win32 v1.05
* Origin: fsxNet Usenet Gateway (21:1/5)

On Tue, 25 Jan 2022 08:29:42 -0800 (PST), "ohg...@gmail.com" <ohger1s@gmail.com> wrote:

Anyone having an issue with Fluke cases getting brittle? I have a 177 that had the battery cover crack in the screw boss area, and the other side won't hold a screw as the inside post is cracked. The plastic is brittle and reminds me of the aging of

plastic in 1990s plastic television cabinets. My 85s never did this and I have a very old 77 that is still in perfect shape although it doesn't get a of use. The 177 is my daily meter and yes, it's fallen a few times.

This might be of interest:
"Problem plastics, types of deterioration & where you find it" <https://mmics.files.wordpress.com/2008/04/problem-plastics-check-list.pdf>

--
Jeff Liebermann jeffl@cruzio.com
PO Box 272 http://www.LearnByDestroying.com
Ben Lomond CA 95005-0272
Skype: JeffLiebermann AE6KS 831-336-2558

--- SoupGate-Win32 v1.05
* Origin: fsxNet Usenet Gateway (21:1/5)

On Tue, 25 Jan 2022 08:29:42 -0800 (PST), "ohg...@gmail.com" <ohger1s@gmail.com> wrote:

Anyone having an issue with Fluke cases getting brittle? I have a 177 that had the battery cover crack in the screw boss area, and the other side won't hold a screw as the inside post is cracked. The plastic is brittle and reminds me of the aging of

plastic in 1990s plastic television cabinets. My 85s never did this and I have a very old 77 that is still in perfect shape although it doesn't get a of use. The 177 is my daily meter and yes, it's fallen a few times.

Any sources of ozone nearby, such as electric motors? A friend, who
owned a machine shop, used to have the same problem with meters after
a few years. However, we're not sure if it's the ozone or the machine
oil in the air that's causing the plastic to become brittle. I also
created some cracking in one of my Fluke meters when I repeatedly used
alcohol to clean the case.

This might be of interest: <https://www.eevblog.com/forum/testgear/fluke-quality/>
Note the photo of the replacement metal hex standoffs for the broken
plastic.

At some point in the past, it became necessary to put additives in the
plastic to make it fire retardant. My guess(tm) is that this has
something to do with the crumbling plastic. Look on the inside of the
case for the acronym that indicates the type of plastic used in your
177.
<https://www.bpf.co.uk/plastipedia/abbreviations/Default.aspx>

--
Jeff Liebermann jeffl@cruzio.com
PO Box 272 http://www.LearnByDestroying.com
Ben Lomond CA 95005-0272
Skype: JeffLiebermann AE6KS 831-336-2558

--- SoupGate-Win32 v1.05
* Origin: fsxNet Usenet Gateway (21:1/5)

Generally, my approach to cracked cases of this nature is to clean thoroughly, add a generous bead of JB-Weld, right up to and including filling the screw holes, allowing it to cure, then drilling out the holes as needed Haven't lost a patient yet. It
may not be the prettiest of cures, but it has the overwhelming virtue of working well.

Peter Wieck
Melrose Park, PA

--- SoupGate-Win32 v1.05
* Origin: fsxNet Usenet Gateway (21:1/5)

On Tuesday, January 25, 2022 at 5:39:58 PM UTC-5, Jeff Liebermann wrote:

On Tue, 25 Jan 2022 08:29:42 -0800 (PST), "ohg...@gmail.com" <ohg...@gmail.com> wrote:

Anyone having an issue with Fluke cases getting brittle? I have a 177 that had the battery cover crack in the screw boss area, and the other side won't hold a screw as the inside post is cracked. The plastic is brittle and reminds me of the aging of

plastic in 1990s plastic television cabinets. My 85s never did this and I have a very old 77 that is still in perfect shape although it doesn't get a of use. The 177 is my daily meter and yes, it's fallen a few times.

Any sources of ozone nearby, such as electric motors?

Nothing out of the ordinary certainly. My older meters have been used in the same environment and never had this issue. I just checked my 40 year old Beckman HD100 that I keep at home. I pulled the back cover to replace the battery last night (
overdue) and flexed the inside plastic parts of the case. Shows no sign of brittleness even when tested with a pocket knife.

At some point in the past, it became necessary to put additives in the plastic to make it fire retardant. My guess(tm) is that this has
something to do with the crumbling plastic.

That makes sense. Unfortunately. Another case of creating far more problems than it solves.

--
Jeff Liebermann je...@cruzio.com
PO Box 272 http://www.LearnByDestroying.com
Ben Lomond CA 95005-0272
Skype: JeffLiebermann AE6KS 831-336-2558

--- SoupGate-Win32 v1.05
* Origin: fsxNet Usenet Gateway (21:1/5)

On Wed, 26 Jan 2022 06:59:27 -0800 (PST), "Peter W."
<peterwieck33@gmail.com> wrote:

Generally, my approach to cracked cases of this nature is to clean thoroughly, add a generous bead of JB-Weld, right up to and including filling the screw holes, allowing it to cure, then drilling out the holes as needed Haven't lost a patient yet. It

may not be the prettiest of cures, but it has the overwhelming virtue of working well.

Peter Wieck
Melrose Park, PA

Good idea. I've done case repairs that way. I have to be careful
which plastic I try to glue. Some of my epoxies don't want to stick.
JB Weld 50139 Plastic Bonder works well enough but takes a full day to
properly harden.

What I've been experimenting with is plastic welding. YouTube videos
showing how it works with a soldering iron: <https://www.youtube.com/results?search_query=plastic+welding> <https://www.harborfreight.com/80-watt-iron-plastic-welding-kit-60662.html>
I didn't do too well because the parts I was trying to weld were too
small or thin.

I also tried hot air. Something like these except I made my own tool: <https://www.amazon.com/hot-air-welder/s?k=hot+air+welder>
I installed a tiny nozzle on my hot air desoldering station for the
welder. I also made a nozzle that heats along a straight seam. I
collected some plastic knife shavings from various junk plastic cases
found around the shop. No need to color match as all the welding is
going to be on the inside of the case. In general, hot air works, but
you have protect nearby parts with an aluminum foil heat shield. Also,
some practice is helpful.

I have the beginnings of a water gas (HHO) hydrogen generator and
torch, which will allow me to make a very narrow hydrogen weld. It's
been sitting for about 3 years waiting for me to finish the build. No
clue if it will weld nicely (or blow up the shop), but it looks
promising.
<https://www.youtube.com/results?search_query=HHO+generator>



--
Jeff Liebermann jeffl@cruzio.com
PO Box 272 http://www.LearnByDestroying.com
Ben Lomond CA 95005-0272
Skype: JeffLiebermann AE6KS 831-336-2558

--- SoupGate-Win32 v1.05
* Origin: fsxNet Usenet Gateway (21:1/5)

On Wednesday, January 26, 2022 at 9:59:30 AM UTC-5, Peter W. wrote:

Generally, my approach to cracked cases of this nature is to clean thoroughly, add a generous bead of JB-Weld, right up to and including filling the screw holes, allowing it to cure, then drilling out the holes as needed Haven't lost a patient yet. It

may not be the prettiest of cures, but it has the overwhelming virtue of working well.

Peter Wieck
Melrose Park, PA

I'll kluge it together at some point, or retire the meter. Haven't decided.

In the meantime, I checked ebay to see if cases were available, and I found one with ---- a cracked battery door same as mine except both sides are cracked *and* it looks like someone already filled the back case with epoxy for a previous failure.
Scroll down the pictures to see the battery door and rear case half. Clearly brittle. Here's a link to the auction and an imgur link of an auction pic that I saved in case anyone sees this years from now after the auction is gone:

https://www.ebay.com/itm/284258608974?hash=item422f22274e:g:3zAAAOSwIshgd~Is

https://i.imgur.com/KOnJnvJ.jpeg

I found a new case on line but its almost as much as the meter cost. <shrug>

--- SoupGate-Win32 v1.05
* Origin: fsxNet Usenet Gateway (21:1/5)

If you have a 3D printer, you could make a replacement battery cover
(or have someone make one for you):
<https://www.yeggi.com/q/fluke+meter/> <https://cults3d.com/en/tags/fluke%20multimeter> <https://mito3d.com/en/3dmodels/search/fluke/all/all/latest/1>
I didn't see anything specific for the 177, but I might have missed
it.
--
Jeff Liebermann jeffl@cruzio.com
PO Box 272 http://www.LearnByDestroying.com
Ben Lomond CA 95005-0272
Skype: JeffLiebermann AE6KS 831-336-2558

--- SoupGate-Win32 v1.05
* Origin: fsxNet Usenet Gateway (21:1/5)

On Wednesday, January 26, 2022 at 1:22:16 PM UTC-5, Jeff Liebermann wrote:

If you have a 3D printer, you could make a replacement battery cover
(or have someone make one for you):
<https://www.yeggi.com/q/fluke+meter/> <https://cults3d.com/en/tags/fluke%20multimeter> <https://mito3d.com/en/3dmodels/search/fluke/all/all/latest/1>
I didn't see anything specific for the 177, but I might have missed
it.
--
Jeff Liebermann je...@cruzio.com
PO Box 272 http://www.LearnByDestroying.com
Ben Lomond CA 95005-0272
Skype: JeffLiebermann AE6KS 831-336-2558

Good idea Jeff. I searched on the link you provided and found this for a 179, but it looks like the 177 and is most likely the same piece.

https://www.thingiverse.com/thing:3867107

--- SoupGate-Win32 v1.05
* Origin: fsxNet Usenet Gateway (21:1/5)