• New Tool

    From Leon@21:1/5 to All on Fri Dec 16 12:02:34 2022
    No I did not buy this tool.

    BUT if you want a tool that can cut mortises for floating tenons faster
    than a classic mortising machine, this might be it.

    Further if you have ever considered getting a Domino for cutting
    mortises for floating tenons but were repulsed by the cost of the
    machine, this might be it.

    HOWEVER if you intend to use this tool extensively you may still want to consider a Domino.

    https://www.youtube.com/shorts/F6coe8_40PI

    I have mentioned many times that I have cut in excess of 10,000 mortises
    with my Domino. I quit counting at that point.

    The above video shows that 4 mortises can be cut in basically 2 minutes,
    or 2 mortises per minute.

    For me, cutting 10,000 mortises with this tool would take 5,000 minutes
    or 83+ hours.


    One last thing to consider for this tool. I cannot find any
    information regarding the ability to make the mortises wider from end to
    end. If that is the case you might as well be using a doweling jig.

    Why? I always use exact fit mortises on one side of the 2 pieces to be joined. I always use the elongated mortise setting for the opposite
    mating piece. Exact fit is exact fit. If all mortises are cut to be
    exact fit and if one on the mating side is not precisely placed you will
    not be able to proper align the pieces. Elongated mortises on the
    opposite mating piece afford you some wiggle room during assembly.

    This new tool from Jessem is approximately 1/3 the price as a Domino.
    Maybe worth it if it will make elongated mating mortises. Not worth it
    if it only makes 1 width, not thickness, mortise.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From DerbyDad03@21:1/5 to Leon on Fri Dec 16 17:20:42 2022
    On Friday, December 16, 2022 at 1:02:42 PM UTC-5, Leon wrote:
    No I did not buy this tool.

    BUT if you want a tool that can cut mortises for floating tenons faster
    than a classic mortising machine, this might be it.

    Further if you have ever considered getting a Domino for cutting
    mortises for floating tenons but were repulsed by the cost of the
    machine, this might be it.

    HOWEVER if you intend to use this tool extensively you may still want to consider a Domino.

    https://www.youtube.com/shorts/F6coe8_40PI

    I have mentioned many times that I have cut in excess of 10,000 mortises with my Domino. I quit counting at that point.

    The above video shows that 4 mortises can be cut in basically 2 minutes,
    or 2 mortises per minute.

    For me, cutting 10,000 mortises with this tool would take 5,000 minutes
    or 83+ hours.


    One last thing to consider for this tool. I cannot find any
    information regarding the ability to make the mortises wider from end to end. If that is the case you might as well be using a doweling jig.

    Why? I always use exact fit mortises on one side of the 2 pieces to be joined. I always use the elongated mortise setting for the opposite
    mating piece. Exact fit is exact fit. If all mortises are cut to be
    exact fit and if one on the mating side is not precisely placed you will
    not be able to proper align the pieces. Elongated mortises on the
    opposite mating piece afford you some wiggle room during assembly.

    This new tool from Jessem is approximately 1/3 the price as a Domino.
    Maybe worth it if it will make elongated mating mortises. Not worth it
    if it only makes 1 width, not thickness, mortise.

    "The Pocket Mill Pro is capable of putting a mortise at the center of a
    3.5” board or 1.75” off the edge of your work piece."

    The board seen at the end of the video has mortises that appear to be
    way beyond 1.75" off the edge.

    I'm assuming they weren't made with the PMP. I know that the Domino
    can put mortises anywhere in the face of any board, but can the PMP?

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From John Grossbohlin@21:1/5 to Leon on Fri Dec 16 17:46:18 2022
    On Friday, December 16, 2022 at 1:02:42 PM UTC-5, Leon wrote:
    No I did not buy this tool.

    I hadn't seen it. Might be useful for one off types of work but it looks tedious for 10K mortises (as would any tool unless it's spread out over years or decades!).

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Leon@21:1/5 to John Grossbohlin on Sat Dec 17 12:03:31 2022
    On 12/16/2022 7:46 PM, John Grossbohlin wrote:
    On Friday, December 16, 2022 at 1:02:42 PM UTC-5, Leon wrote:
    No I did not buy this tool.

    I hadn't seen it. Might be useful for one off types of work but it looks tedious for 10K mortises (as would any tool unless it's spread out over years or decades!).


    It is the kind of mortise maker that you may not realize is as useful as
    you think. Mortises are a PIA even with a traditional mortiser because
    of the multiple passes needed not to mention using it to cut a mortise
    in the middle od a panel.

    While more expensive than my old bench top mortiser it does appear to
    make clean mortises.

    I bought my Domino almost 16 years ago and hoped that I would get some
    use out of it. Wow, I did get some use out of it.

    I would be fearful that if some one buys the Jessem tool for this
    purpose that they might find that this makes cutting mortises very easy
    and quick compared to a traditional mortiser. And I fear that they
    would grow tired quickly of the back and forth hand motion and then
    upgrade to the Domino. BUT maybe not if not building more than one or
    two pieces a year.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Scott Lurndal@21:1/5 to Leon on Sat Dec 17 19:05:19 2022
    Leon <lcb11211@swbelldotnet> writes:
    On 12/16/2022 7:46 PM, John Grossbohlin wrote:
    On Friday, December 16, 2022 at 1:02:42 PM UTC-5, Leon wrote:
    No I did not buy this tool.

    I hadn't seen it. Might be useful for one off types of work but it looks tedious for 10K mortises (as would any tool unless it's spread out over years or decades!).


    It is the kind of mortise maker that you may not realize is as useful as
    you think. Mortises are a PIA even with a traditional mortiser because
    of the multiple passes needed not to mention using it to cut a mortise
    in the middle od a panel.

    I assume you are referring to the relatively inexpensive hollow
    chisel mortisers. A chain mortiser is much quicker, albeit
    considerably more expensive.

    https://www.timbertools.com/Chain-Mortisers/

    I have a Laguna horizontal mortiser, which generally works
    more quickly than either of the hollow chisel mortisers I used
    to use (both a drill-press attachment and a small standalone
    (General International) HC mortiser). With the Laguna, you
    either need to round the ends of of the tenon or hand-chisel
    it to square.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From ritzannaseaton@gmail.com@21:1/5 to Scott Lurndal on Sun Dec 18 21:22:53 2022
    On Saturday, December 17, 2022 at 1:05:24 PM UTC-6, Scott Lurndal wrote:
    Leon <lcb11211@swbelldotnet> writes:
    On 12/16/2022 7:46 PM, John Grossbohlin wrote:
    On Friday, December 16, 2022 at 1:02:42 PM UTC-5, Leon wrote:
    No I did not buy this tool.

    I hadn't seen it. Might be useful for one off types of work but it looks tedious for 10K mortises (as would any tool unless it's spread out over years or decades!).


    It is the kind of mortise maker that you may not realize is as useful as >you think. Mortises are a PIA even with a traditional mortiser because
    of the multiple passes needed not to mention using it to cut a mortise
    in the middle od a panel.
    I assume you are referring to the relatively inexpensive hollow
    chisel mortisers. A chain mortiser is much quicker, albeit
    considerably more expensive.

    https://www.timbertools.com/Chain-Mortisers/

    I have a Laguna horizontal mortiser, which generally works
    more quickly than either of the hollow chisel mortisers I used
    to use (both a drill-press attachment and a small standalone
    (General International) HC mortiser). With the Laguna, you
    either need to round the ends of of the tenon or hand-chisel
    it to square.

    I did a Google search for Laguna horizontal mortiser. But could not find any pictures. A am guessing it is similar to the European Felder model. It was a machine with a table and a couple levers. And a motor driven chuck that held a drill bit, cutter.
    Clamped your wood piece to the table and used the levers to move the wood side to side and in and out to cut a mortise. There are stops to set on the table to limit the size of the mortise. MiniMax has bolt on tables for its jointer/planer and
    presume jointer. Uses the cutter block to hold a bit in the end. Then put the table on the machine and rout, cut, the mortise.

    These horizontal mortising machines seem ideal for making a few big mortises. Such as when building a door. Make the mortises any length and mill your slip tenon to whatever size you need. Different cutter bits determine the thickness of the mortise.
    Probably anything from 6mm up to 20mm.

    Again, for a few mortises, slip tenons, these horizontal mortisers seem great. But for doing dozens and dozens of mortises on small pieces or big pieces too big to fit onto the machines, the Festool Domino seems the way to go. Not sure on the Jessem
    device Leon had in the video. It would seem to work in some situations but not all situations. Unlike the Domino. I would be worried with the Jessem mortiser that after buying it and using it, I would see all of its short comings and all the things it
    cannot do very well. And then wish I had just paid the 3-4 times more for the Domino up front. I would be worried it might be like drills. A 3/8 keyed chuck electric drill is good. You can do lots of work with it. Drilling and driving. But after
    you use a cordless drill, the old electric drill doesn't get much use anymore. And then add an impact driver, and it gets even less use. And add a Milwaukee Hole Hawg or a right angle drill, if you are an electrician, and the old 3/8 electric collects
    even more dust. The Jessem mortiser thing might make you sad at how much it can't do compared to the more expensive real tools.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Leon@21:1/5 to Scott Lurndal on Mon Dec 19 09:58:54 2022
    On 12/17/2022 1:05 PM, Scott Lurndal wrote:
    Leon <lcb11211@swbelldotnet> writes:
    On 12/16/2022 7:46 PM, John Grossbohlin wrote:
    On Friday, December 16, 2022 at 1:02:42 PM UTC-5, Leon wrote:
    No I did not buy this tool.

    I hadn't seen it. Might be useful for one off types of work but it looks tedious for 10K mortises (as would any tool unless it's spread out over years or decades!).


    It is the kind of mortise maker that you may not realize is as useful as
    you think. Mortises are a PIA even with a traditional mortiser because
    of the multiple passes needed not to mention using it to cut a mortise
    in the middle od a panel.

    I assume you are referring to the relatively inexpensive hollow
    chisel mortisers. A chain mortiser is much quicker, albeit
    considerably more expensive.

    https://www.timbertools.com/Chain-Mortisers/

    I have a Laguna horizontal mortiser, which generally works
    more quickly than either of the hollow chisel mortisers I used
    to use (both a drill-press attachment and a small standalone
    (General International) HC mortiser). With the Laguna, you
    either need to round the ends of of the tenon or hand-chisel
    it to square.



    Ah, Found that oscillating chisel mortiser. Although the bits seem to
    be a different design than described in my previous reply, it works on
    the same principal.

    https://www.youtube.com/watch?v=HEn4MPfkNDM

    And one with a similar cutter that I saw way back when.

    https://www.youtube.com/watch?v=nCrzbnArvb8

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Leon@21:1/5 to Scott Lurndal on Mon Dec 19 09:39:30 2022
    On 12/17/2022 1:05 PM, Scott Lurndal wrote:
    Leon <lcb11211@swbelldotnet> writes:
    On 12/16/2022 7:46 PM, John Grossbohlin wrote:
    On Friday, December 16, 2022 at 1:02:42 PM UTC-5, Leon wrote:
    No I did not buy this tool.

    I hadn't seen it. Might be useful for one off types of work but it looks tedious for 10K mortises (as would any tool unless it's spread out over years or decades!).


    It is the kind of mortise maker that you may not realize is as useful as
    you think. Mortises are a PIA even with a traditional mortiser because
    of the multiple passes needed not to mention using it to cut a mortise
    in the middle od a panel.

    I assume you are referring to the relatively inexpensive hollow
    chisel mortisers. A chain mortiser is much quicker, albeit
    considerably more expensive.

    Yes! The hollow chisel variety. The chain looks very interesting. It appears, from your link that small mortises might not be possible, those
    like the ones that the Domino, and or the hollow chisel variety can
    make. And the bottoms are probably round. That could be good for
    excess glue.




    https://www.timbertools.com/Chain-Mortisers/

    I have a Laguna horizontal mortiser, which generally works
    more quickly than either of the hollow chisel mortisers I used
    to use (both a drill-press attachment and a small standalone
    (General International) HC mortiser). With the Laguna, you
    either need to round the ends of of the tenon or hand-chisel
    it to square.

    Yeah! When I was looking at jointer/planer combos from Hammer a couple
    of years back I saw that some offered the mortiser attachment. Those
    would be fast especially for larger mortises.

    Is your Laguna a stand alone unit? Those look pretty stout. It's
    mortises are much like the Domino mortises. I suppose you use or could
    use a bull nose router bit to make your tenons.

    On another note I saw a mortiser several years ago that had an isolating straight cutter. It sorta looked "t" shaped on the business end and the
    ends of the t's, the left and right side, cut into the wood as it
    plunged. Because of the "t" shape it did not take big bites of wood, so
    it was a blur when operating and plunging.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Scott Lurndal@21:1/5 to Leon on Mon Dec 19 16:43:06 2022
    Leon <lcb11211@swbelldotnet> writes:
    On 12/17/2022 1:05 PM, Scott Lurndal wrote:


    I have a Laguna horizontal mortiser, which generally works
    more quickly than either of the hollow chisel mortisers I used
    to use (both a drill-press attachment and a small standalone
    (General International) HC mortiser). With the Laguna, you
    either need to round the ends of of the tenon or hand-chisel
    it to square.

    Yeah! When I was looking at jointer/planer combos from Hammer a couple
    of years back I saw that some offered the mortiser attachment. Those
    would be fast especially for larger mortises.

    Is your Laguna a stand alone unit? Those look pretty stout. It's
    mortises are much like the Domino mortises. I suppose you use or could
    use a bull nose router bit to make your tenons.

    I have an older one, it is stand-alone. The bits need to be fairly long (3-4"),
    I don't think a bullnose router bit would be workable.

    I had to build some sway braces[*] for it bolted to the floor to get the highest quality mortices with it. They no longer sell this model, but rather more expensive (and better quality) models.

    [*] 1/2" EMT, flattened drilled ends to bolt to the back of the head unit
    and the floor.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From krw@notreal.com@21:1/5 to ritzannaseaton@gmail.com on Mon Dec 19 15:08:35 2022
    On Sun, 18 Dec 2022 21:22:53 -0800 (PST), "russellseaton1@yahoo.com" <ritzannaseaton@gmail.com> wrote:

    On Saturday, December 17, 2022 at 1:05:24 PM UTC-6, Scott Lurndal wrote:
    Leon <lcb11211@swbelldotnet> writes:
    On 12/16/2022 7:46 PM, John Grossbohlin wrote:
    On Friday, December 16, 2022 at 1:02:42 PM UTC-5, Leon wrote:
    No I did not buy this tool.

    I hadn't seen it. Might be useful for one off types of work but it looks tedious for 10K mortises (as would any tool unless it's spread out over years or decades!).


    It is the kind of mortise maker that you may not realize is as useful as
    you think. Mortises are a PIA even with a traditional mortiser because
    of the multiple passes needed not to mention using it to cut a mortise
    in the middle od a panel.
    I assume you are referring to the relatively inexpensive hollow
    chisel mortisers. A chain mortiser is much quicker, albeit
    considerably more expensive.

    https://www.timbertools.com/Chain-Mortisers/

    I have a Laguna horizontal mortiser, which generally works
    more quickly than either of the hollow chisel mortisers I used
    to use (both a drill-press attachment and a small standalone
    (General International) HC mortiser). With the Laguna, you
    either need to round the ends of of the tenon or hand-chisel
    it to square.

    I did a Google search for Laguna horizontal mortiser. But could not find any pictures. A am guessing it is similar to the European Felder model. It was a machine with a table and a couple levers. And a motor driven chuck that held a drill bit,
    cutter. Clamped your wood piece to the table and used the levers to move the wood side to side and in and out to cut a mortise. There are stops to set on the table to limit the size of the mortise. MiniMax has bolt on tables for its jointer/planer and
    presume jointer. Uses the cutter block to hold a bit in the end. Then put the table on the machine and rout, cut, the mortise.

    I found (I think) a picture. <https://images-na.ssl-images-amazon.com/images/I/31VR6ogvENL._AC_.jpg>

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From ritzannaseaton@gmail.com@21:1/5 to k...@notreal.com on Mon Dec 19 13:07:15 2022
    On Monday, December 19, 2022 at 2:08:42 PM UTC-6, k...@notreal.com wrote:
    On Sun, 18 Dec 2022 21:22:53 -0800 (PST), "russell...@yahoo.com" <ritzann...@gmail.com> wrote:

    On Saturday, December 17, 2022 at 1:05:24 PM UTC-6, Scott Lurndal wrote:
    Leon <lcb11211@swbelldotnet> writes:
    On 12/16/2022 7:46 PM, John Grossbohlin wrote:
    On Friday, December 16, 2022 at 1:02:42 PM UTC-5, Leon wrote:
    No I did not buy this tool.

    I hadn't seen it. Might be useful for one off types of work but it looks tedious for 10K mortises (as would any tool unless it's spread out over years or decades!).


    It is the kind of mortise maker that you may not realize is as useful as >> >you think. Mortises are a PIA even with a traditional mortiser because >> >of the multiple passes needed not to mention using it to cut a mortise >> >in the middle od a panel.
    I assume you are referring to the relatively inexpensive hollow
    chisel mortisers. A chain mortiser is much quicker, albeit
    considerably more expensive.

    https://www.timbertools.com/Chain-Mortisers/

    I have a Laguna horizontal mortiser, which generally works
    more quickly than either of the hollow chisel mortisers I used
    to use (both a drill-press attachment and a small standalone
    (General International) HC mortiser). With the Laguna, you
    either need to round the ends of of the tenon or hand-chisel
    it to square.

    I did a Google search for Laguna horizontal mortiser. But could not find any pictures. A am guessing it is similar to the European Felder model. It was a machine with a table and a couple levers. And a motor driven chuck that held a drill bit, cutter.
    Clamped your wood piece to the table and used the levers to move the wood side to side and in and out to cut a mortise. There are stops to set on the table to limit the size of the mortise. MiniMax has bolt on tables for its jointer/planer and presume
    jointer. Uses the cutter block to hold a bit in the end. Then put the table on the machine and rout, cut, the mortise.
    I found (I think) a picture. <https://images-na.ssl-images-amazon.com/images/I/31VR6ogvENL._AC_.jpg>

    Yes. Identical, sort of, to the Felder FD 250. Except 100% opposite. It looks like the motor and bit move with the Felder model. Whereas the Laguna has the motor and bit fixed in place and you move the wood on a moving table.

    Laguna
    https://images-na.ssl-images-amazon.com/images/I/31VR6ogvENL._AC_.jpg

    Felder https://www.felder-group.com/en-us/products/boring-and-mortising-machines-c1959/horizontal-mortiser-fd-250-p3016

    I could be misinterpreting the Felder picture. Maybe its lever moves the wood too, instead of the motor. Not sure.

    With the MiniMax jointer, and combination jointer/planer, it does have a chuck you can mount on the end of the jointer cutter head. And a separate bolt on mortising table. You clamp the wood onto the separate bolt on table. Then use a couple levers to
    move the wood and table. Motor and bit are fixed in place.

    Here is a video of the mortiser attached to a MiniMax full combination machine. Same table attaches to the combo jointer/planer.
    https://www.youtube.com/watch?v=e8WnAADN0SI

    Here is the SCM horizontal mortiser. https://www.scmgroup.com/en_US/scmwood/products/joinery-machines.c884/horizontal-mortiser.7925/minimax-as-16.61049

    Here is a discussion about the bolt on horizontal mortiser for the MiniMax machine. Kind of gives some real world examples of when or if you want it. I know it is completely unrelated to the original point of this thread. But this is the internet!!!!!!
    https://sawmillcreek.org/showthread.php?159397-MiniMax-mortiser-attachment

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Scott Lurndal@21:1/5 to krw@notreal.com on Mon Dec 19 20:30:33 2022
    krw@notreal.com writes:
    On Sun, 18 Dec 2022 21:22:53 -0800 (PST), "russellseaton1@yahoo.com" ><ritzannaseaton@gmail.com> wrote:

    On Saturday, December 17, 2022 at 1:05:24 PM UTC-6, Scott Lurndal wrote:
    Leon <lcb11211@swbelldotnet> writes:
    On 12/16/2022 7:46 PM, John Grossbohlin wrote:
    On Friday, December 16, 2022 at 1:02:42 PM UTC-5, Leon wrote:
    No I did not buy this tool.

    I hadn't seen it. Might be useful for one off types of work but it looks tedious for 10K mortises (as would any tool unless it's spread out over years or decades!).


    It is the kind of mortise maker that you may not realize is as useful as >>> >you think. Mortises are a PIA even with a traditional mortiser because
    of the multiple passes needed not to mention using it to cut a mortise
    in the middle od a panel.
    I assume you are referring to the relatively inexpensive hollow
    chisel mortisers. A chain mortiser is much quicker, albeit
    considerably more expensive.

    https://www.timbertools.com/Chain-Mortisers/

    I have a Laguna horizontal mortiser, which generally works
    more quickly than either of the hollow chisel mortisers I used
    to use (both a drill-press attachment and a small standalone
    (General International) HC mortiser). With the Laguna, you
    either need to round the ends of of the tenon or hand-chisel
    it to square.

    I did a Google search for Laguna horizontal mortiser. But could not find any pictures. A am guessing it is similar to the European Felder model. It was a machine with a table and a couple levers. And a motor driven chuck that held a drill bit,
    cutter. Clamped your wood piece to the table and used the levers to move the wood side to side and in and out to cut a mortise. There are stops to set on the table to limit the size of the mortise. MiniMax has bolt on tables for its jointer/planer and
    presume jointer. Uses the cutter block to hold a bit in the end. Then put the table on the machine and rout, cut, the mortise.

    I found (I think) a picture. ><https://images-na.ssl-images-amazon.com/images/I/31VR6ogvENL._AC_.jpg>


    That is it.

    The column isn't really very sturdy, so it helps to both bolt the base
    to the floor and brace the head unit (there are two mounting points
    for this purpose in the back of the motor enclosure).

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Leon@21:1/5 to Scott Lurndal on Mon Dec 19 16:09:29 2022
    On 12/19/2022 10:43 AM, Scott Lurndal wrote:
    Leon <lcb11211@swbelldotnet> writes:
    On 12/17/2022 1:05 PM, Scott Lurndal wrote:


    I have a Laguna horizontal mortiser, which generally works
    more quickly than either of the hollow chisel mortisers I used
    to use (both a drill-press attachment and a small standalone
    (General International) HC mortiser). With the Laguna, you
    either need to round the ends of of the tenon or hand-chisel
    it to square.

    Yeah! When I was looking at jointer/planer combos from Hammer a couple
    of years back I saw that some offered the mortiser attachment. Those
    would be fast especially for larger mortises.

    Is your Laguna a stand alone unit? Those look pretty stout. It's
    mortises are much like the Domino mortises. I suppose you use or could
    use a bull nose router bit to make your tenons.

    I have an older one, it is stand-alone. The bits need to be fairly long (3-4"),
    I don't think a bullnose router bit would be workable.

    If the mortise is only as wide as the bit making the mortise the bull
    nose bit of the same diameter should work. If your mortises are wider
    than the bit doing the cutting, that would require 4 passes on a round
    over bit of the same radius as the cutter on all 4 corners.





    I had to build some sway braces[*] for it bolted to the floor to get the highest quality mortices with it. They no longer sell this model, but rather more expensive (and better quality) models.

    [*] 1/2" EMT, flattened drilled ends to bolt to the back of the head unit
    and the floor.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From DerbyDad03@21:1/5 to Leon on Wed Dec 21 04:17:07 2022
    On Friday, December 16, 2022 at 1:02:42 PM UTC-5, Leon wrote:
    No I did not buy this tool.

    BUT if you want a tool that can cut mortises for floating tenons faster
    than a classic mortising machine, this might be it.

    Further if you have ever considered getting a Domino for cutting
    mortises for floating tenons but were repulsed by the cost of the
    machine, this might be it.

    HOWEVER if you intend to use this tool extensively you may still want to consider a Domino.

    https://www.youtube.com/shorts/F6coe8_40PI

    I have mentioned many times that I have cut in excess of 10,000 mortises with my Domino. I quit counting at that point.

    The above video shows that 4 mortises can be cut in basically 2 minutes,
    or 2 mortises per minute.

    For me, cutting 10,000 mortises with this tool would take 5,000 minutes
    or 83+ hours.


    One last thing to consider for this tool. I cannot find any
    information regarding the ability to make the mortises wider from end to end. If that is the case you might as well be using a doweling jig.

    Why? I always use exact fit mortises on one side of the 2 pieces to be joined. I always use the elongated mortise setting for the opposite
    mating piece. Exact fit is exact fit. If all mortises are cut to be
    exact fit and if one on the mating side is not precisely placed you will
    not be able to proper align the pieces. Elongated mortises on the
    opposite mating piece afford you some wiggle room during assembly.

    This new tool from Jessem is approximately 1/3 the price as a Domino.
    Maybe worth it if it will make elongated mating mortises. Not worth it
    if it only makes 1 width, not thickness, mortise.

    I’m not sure if you saw my earlier post. Can the tool make the mortises
    that are shown in the middle of the wide board at the end of the video?
    Based on the description, it doesn’t seem like it could.

    My previous post…

    "The Pocket Mill Pro is capable of putting a mortise at the center of a
    3.5” board or 1.75” off the edge of your work piece."

    The board seen at the end of the video has mortises that appear to be
    way beyond 1.75" off the edge.

    I'm assuming they weren't made with the PMP. I know that the Domino
    can put mortises anywhere in the face of any board, but can the PMP?”

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Leon@21:1/5 to All on Wed Dec 21 09:45:06 2022
    On 12/21/2022 6:17 AM, DerbyDad03 wrote:
    On Friday, December 16, 2022 at 1:02:42 PM UTC-5, Leon wrote:
    No I did not buy this tool.

    BUT if you want a tool that can cut mortises for floating tenons faster
    than a classic mortising machine, this might be it.

    Further if you have ever considered getting a Domino for cutting
    mortises for floating tenons but were repulsed by the cost of the
    machine, this might be it.

    HOWEVER if you intend to use this tool extensively you may still want to
    consider a Domino.

    https://www.youtube.com/shorts/F6coe8_40PI

    I have mentioned many times that I have cut in excess of 10,000 mortises
    with my Domino. I quit counting at that point.

    The above video shows that 4 mortises can be cut in basically 2 minutes,
    or 2 mortises per minute.

    For me, cutting 10,000 mortises with this tool would take 5,000 minutes
    or 83+ hours.


    One last thing to consider for this tool. I cannot find any
    information regarding the ability to make the mortises wider from end to
    end. If that is the case you might as well be using a doweling jig.

    Why? I always use exact fit mortises on one side of the 2 pieces to be
    joined. I always use the elongated mortise setting for the opposite
    mating piece. Exact fit is exact fit. If all mortises are cut to be
    exact fit and if one on the mating side is not precisely placed you will
    not be able to proper align the pieces. Elongated mortises on the
    opposite mating piece afford you some wiggle room during assembly.

    This new tool from Jessem is approximately 1/3 the price as a Domino.
    Maybe worth it if it will make elongated mating mortises. Not worth it
    if it only makes 1 width, not thickness, mortise.

    I’m not sure if you saw my earlier post. Can the tool make the mortises that are shown in the middle of the wide board at the end of the video?
    Based on the description, it doesn’t seem like it could.

    I would assume so, how else would the mortises have been placed?


    My previous post…

    "The Pocket Mill Pro is capable of putting a mortise at the center of a 3.5” board or 1.75” off the edge of your work piece."

    The board seen at the end of the video has mortises that appear to be
    way beyond 1.75" off the edge.

    I'm assuming they weren't made with the PMP. I know that the Domino
    can put mortises anywhere in the face of any board, but can the PMP?”


    FWIW this PMP cannot make wider mortises, like the Domino, unless you
    move the tool over. It cuts a fixed width. That wold be a hard no
    for me.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From ritzannaseaton@gmail.com@21:1/5 to All on Wed Dec 21 16:38:45 2022
    On Wednesday, December 21, 2022 at 6:17:11 AM UTC-6, DerbyDad03 wrote:
    On Friday, December 16, 2022 at 1:02:42 PM UTC-5, Leon wrote:
    No I did not buy this tool.

    BUT if you want a tool that can cut mortises for floating tenons faster than a classic mortising machine, this might be it.

    Further if you have ever considered getting a Domino for cutting
    mortises for floating tenons but were repulsed by the cost of the
    machine, this might be it.

    HOWEVER if you intend to use this tool extensively you may still want to consider a Domino.

    https://www.youtube.com/shorts/F6coe8_40PI

    I have mentioned many times that I have cut in excess of 10,000 mortises with my Domino. I quit counting at that point.

    The above video shows that 4 mortises can be cut in basically 2 minutes, or 2 mortises per minute.

    For me, cutting 10,000 mortises with this tool would take 5,000 minutes
    or 83+ hours.


    One last thing to consider for this tool. I cannot find any
    information regarding the ability to make the mortises wider from end to end. If that is the case you might as well be using a doweling jig.

    Why? I always use exact fit mortises on one side of the 2 pieces to be joined. I always use the elongated mortise setting for the opposite
    mating piece. Exact fit is exact fit. If all mortises are cut to be
    exact fit and if one on the mating side is not precisely placed you will not be able to proper align the pieces. Elongated mortises on the
    opposite mating piece afford you some wiggle room during assembly.

    This new tool from Jessem is approximately 1/3 the price as a Domino. Maybe worth it if it will make elongated mating mortises. Not worth it
    if it only makes 1 width, not thickness, mortise.
    I’m not sure if you saw my earlier post. Can the tool make the mortises that are shown in the middle of the wide board at the end of the video? Based on the description, it doesn’t seem like it could.

    My previous post…
    "The Pocket Mill Pro is capable of putting a mortise at the center of a 3.5” board or 1.75” off the edge of your work piece."

    The board seen at the end of the video has mortises that appear to be
    way beyond 1.75" off the edge.

    I'm assuming they weren't made with the PMP. I know that the Domino
    can put mortises anywhere in the face of any board, but can the PMP?”

    https://jessem.com/products/pocket-mill-pro-loose-tenon-system
    This is a video from the Jessem website on this tool. It looks like you can undo the right angle support and lay the tool flat onto a piece of wood. And drill the mortises in the middle of the board. You would likely need to use some long boards/
    battens and clamps to hold the jig in place in the middle of the board. At 0:35 in the video you can see the right angle attachment separated from the working part of the jig. So then the drill guide and back and forth part of the jog could be clamped
    flat in the middle of a board. Maybe?

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From DerbyDad03@21:1/5 to russellseaton1@yahoo.com on Wed Dec 21 22:47:44 2022
    On Wednesday, December 21, 2022 at 7:38:47 PM UTC-5, russellseaton1@yahoo.com wrote:
    On Wednesday, December 21, 2022 at 6:17:11 AM UTC-6, DerbyDad03 wrote:
    On Friday, December 16, 2022 at 1:02:42 PM UTC-5, Leon wrote:
    No I did not buy this tool.

    BUT if you want a tool that can cut mortises for floating tenons faster than a classic mortising machine, this might be it.

    Further if you have ever considered getting a Domino for cutting mortises for floating tenons but were repulsed by the cost of the machine, this might be it.

    HOWEVER if you intend to use this tool extensively you may still want to consider a Domino.

    https://www.youtube.com/shorts/F6coe8_40PI

    I have mentioned many times that I have cut in excess of 10,000 mortises with my Domino. I quit counting at that point.

    The above video shows that 4 mortises can be cut in basically 2 minutes, or 2 mortises per minute.

    For me, cutting 10,000 mortises with this tool would take 5,000 minutes or 83+ hours.


    One last thing to consider for this tool. I cannot find any
    information regarding the ability to make the mortises wider from end to end. If that is the case you might as well be using a doweling jig.

    Why? I always use exact fit mortises on one side of the 2 pieces to be joined. I always use the elongated mortise setting for the opposite mating piece. Exact fit is exact fit. If all mortises are cut to be exact fit and if one on the mating side is not precisely placed you will not be able to proper align the pieces. Elongated mortises on the opposite mating piece afford you some wiggle room during assembly.

    This new tool from Jessem is approximately 1/3 the price as a Domino. Maybe worth it if it will make elongated mating mortises. Not worth it if it only makes 1 width, not thickness, mortise.
    I’m not sure if you saw my earlier post. Can the tool make the mortises that are shown in the middle of the wide board at the end of the video? Based on the description, it doesn’t seem like it could.

    My previous post…
    "The Pocket Mill Pro is capable of putting a mortise at the center of a 3.5” board or 1.75” off the edge of your work piece."

    The board seen at the end of the video has mortises that appear to be
    way beyond 1.75" off the edge.

    I'm assuming they weren't made with the PMP. I know that the Domino
    can put mortises anywhere in the face of any board, but can the PMP?”
    https://jessem.com/products/pocket-mill-pro-loose-tenon-system
    This is a video from the Jessem website on this tool. It looks like you can undo the right angle support and lay the tool flat onto a piece of wood. And drill the mortises in the middle of the board. You would likely need to use some long boards/
    battens and clamps to hold the jig in place in the middle of the board. At 0:35 in the video you can see the right angle attachment separated from the working part of the jig. So then the drill guide and back and forth part of the jog could be clamped
    flat in the middle of a board. Maybe?

    I’ll have to go with your “maybe”. They never show the tool
    being used in that manner or even mentioning it. On the page
    that you linked to there’s a section entitled “Referencing
    Your Cut”. Click the plus sign and the following text appears:

    “The Pocket Mill Pro comes with a laser engraved referencing
    window. Simply loosen the large knob and slide the upper unit
    back. Line up your material to where you want the mortise and
    slide and lock the upper unit back in position and you’re ready
    to cut. The Pocket Mill Pro is capable of putting a mortise at the
    center of a 3.5” board or 1.75” off the edge of your work piece.”

    There’s no mention of removing the fence and using the tool
    in the middle of a wide board. In fact, they specifically mention
    what the tool is “capable” of doing. 1.75” off the edge.

    I might just give them a call and get a direct answer. Might. ;-)

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From John Grossbohlin@21:1/5 to All on Thu Dec 22 06:11:17 2022
    On Thursday, December 22, 2022 at 1:47:51 AM UTC-5, DerbyDad03 wrote:

    There’s no mention of removing the fence and using the tool
    in the middle of a wide board. In fact, they specifically mention
    what the tool is “capable” of doing. 1.75” off the edge.

    I might just give them a call and get a direct answer. Might. ;-)

    Seems like removing the fence and indexing off a board or straight edge clamp would be a "normal" application of such a tool... No?

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Leon@21:1/5 to All on Thu Dec 22 13:03:50 2022
    On 12/22/2022 12:47 AM, DerbyDad03 wrote:
    On Wednesday, December 21, 2022 at 7:38:47 PM UTC-5, russellseaton1@yahoo.com wrote:
    On Wednesday, December 21, 2022 at 6:17:11 AM UTC-6, DerbyDad03 wrote:
    On Friday, December 16, 2022 at 1:02:42 PM UTC-5, Leon wrote:
    No I did not buy this tool.

    BUT if you want a tool that can cut mortises for floating tenons faster >>>> than a classic mortising machine, this might be it.

    Further if you have ever considered getting a Domino for cutting
    mortises for floating tenons but were repulsed by the cost of the
    machine, this might be it.

    HOWEVER if you intend to use this tool extensively you may still want to >>>> consider a Domino.

    https://www.youtube.com/shorts/F6coe8_40PI

    I have mentioned many times that I have cut in excess of 10,000 mortises >>>> with my Domino. I quit counting at that point.

    The above video shows that 4 mortises can be cut in basically 2 minutes, >>>> or 2 mortises per minute.

    For me, cutting 10,000 mortises with this tool would take 5,000 minutes >>>> or 83+ hours.


    One last thing to consider for this tool. I cannot find any
    information regarding the ability to make the mortises wider from end to >>>> end. If that is the case you might as well be using a doweling jig.

    Why? I always use exact fit mortises on one side of the 2 pieces to be >>>> joined. I always use the elongated mortise setting for the opposite
    mating piece. Exact fit is exact fit. If all mortises are cut to be
    exact fit and if one on the mating side is not precisely placed you will >>>> not be able to proper align the pieces. Elongated mortises on the
    opposite mating piece afford you some wiggle room during assembly.

    This new tool from Jessem is approximately 1/3 the price as a Domino.
    Maybe worth it if it will make elongated mating mortises. Not worth it >>>> if it only makes 1 width, not thickness, mortise.
    I’m not sure if you saw my earlier post. Can the tool make the mortises >>> that are shown in the middle of the wide board at the end of the video?
    Based on the description, it doesn’t seem like it could.

    My previous post…
    "The Pocket Mill Pro is capable of putting a mortise at the center of a
    3.5” board or 1.75” off the edge of your work piece."

    The board seen at the end of the video has mortises that appear to be
    way beyond 1.75" off the edge.

    I'm assuming they weren't made with the PMP. I know that the Domino
    can put mortises anywhere in the face of any board, but can the PMP?”
    https://jessem.com/products/pocket-mill-pro-loose-tenon-system
    This is a video from the Jessem website on this tool. It looks like you can undo the right angle support and lay the tool flat onto a piece of wood. And drill the mortises in the middle of the board. You would likely need to use some long boards/
    battens and clamps to hold the jig in place in the middle of the board. At 0:35 in the video you can see the right angle attachment separated from the working part of the jig. So then the drill guide and back and forth part of the jog could be clamped
    flat in the middle of a board. Maybe?

    I’ll have to go with your “maybe”. They never show the tool
    being used in that manner or even mentioning it. On the page
    that you linked to there’s a section entitled “Referencing
    Your Cut”. Click the plus sign and the following text appears:

    “The Pocket Mill Pro comes with a laser engraved referencing
    window. Simply loosen the large knob and slide the upper unit
    back. Line up your material to where you want the mortise and
    slide and lock the upper unit back in position and you’re ready
    to cut. The Pocket Mill Pro is capable of putting a mortise at the
    center of a 3.5” board or 1.75” off the edge of your work piece.”

    There’s no mention of removing the fence and using the tool
    in the middle of a wide board. In fact, they specifically mention
    what the tool is “capable” of doing. 1.75” off the edge.

    I might just give them a call and get a direct answer. Might. ;-)


    Or leave a comment on the video. I did that and learned to make an
    elongated mortise that you need to move the tool or the work over a bit.

    This thing is half baked and there are a lot of, IMHO, necessary
    features it would need to have before I would consider one.
    Unfortunately some of these tool companies, and Woodpeckers, dream up
    tools and there seems to be no woodworker feed back to help with the design.

    I will say that some of these tools are great, some rushed to market.

    Unfortunately for novice woodworkers they don't know how much they don't
    know and jump on something like this.

    I'll look into making another comment on the video concerning the
    mortises on the side of a panel.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From DerbyDad03@21:1/5 to gros...@gmail.com on Thu Dec 22 16:56:47 2022
    On Thursday, December 22, 2022 at 9:11:20 AM UTC-5, gros...@gmail.com wrote:
    On Thursday, December 22, 2022 at 1:47:51 AM UTC-5, DerbyDad03 wrote:

    There’s no mention of removing the fence and using the tool
    in the middle of a wide board. In fact, they specifically mention
    what the tool is “capable” of doing. 1.75” off the edge.

    I might just give them a call and get a direct answer. Might. ;-)
    Seems like removing the fence and indexing off a board or straight edge clamp would be a "normal" application of such a tool... No?

    I tend to agree, but they don't mention it or show it, yet they specifically mention
    the 'capability' being "putting a mortise at the center of a 3.5” board or 1.75” off
    the edge of your work piece." One could easily read that as the *limit* of the tool's
    capability.

    Maybe their ad writers either don't know or didn't think ahead far enough to word it
    differently. Something like this makes it much clearer and makes the tool sound more
    versatile. Assuming it's true. ;-)

    "With the included fence, the Pocket Mill Pro is capable of putting a mortise at the
    center of a 3.5” board or 1.75” off the edge of your work piece. Removing the fence
    allows the user to put a mortise at any location they choose."

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Leon@21:1/5 to All on Fri Dec 23 12:03:05 2022
    On 12/22/2022 6:56 PM, DerbyDad03 wrote:
    On Thursday, December 22, 2022 at 9:11:20 AM UTC-5, gros...@gmail.com wrote:
    On Thursday, December 22, 2022 at 1:47:51 AM UTC-5, DerbyDad03 wrote:

    There’s no mention of removing the fence and using the tool
    in the middle of a wide board. In fact, they specifically mention
    what the tool is “capable” of doing. 1.75” off the edge.

    I might just give them a call and get a direct answer. Might. ;-)
    Seems like removing the fence and indexing off a board or straight edge clamp would be a "normal" application of such a tool... No?

    I tend to agree, but they don't mention it or show it, yet they specifically mention
    the 'capability' being "putting a mortise at the center of a 3.5” board or 1.75” off
    the edge of your work piece." One could easily read that as the *limit* of the tool's
    capability.

    Maybe their ad writers either don't know or didn't think ahead far enough to word it
    differently. Something like this makes it much clearer and makes the tool sound more
    versatile. Assuming it's true. ;-)

    "With the included fence, the Pocket Mill Pro is capable of putting a mortise at the
    center of a 3.5” board or 1.75” off the edge of your work piece. Removing the fence
    allows the user to put a mortise at any location they choose."


    Ok, I got a reply, you have to remove a part and attach a part. The
    part to attach has not yet been fully developed and will apparently be
    an add-on accessory. If the accessories are as expensive as this
    incomplete jig you might as well go for the Domino.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From DerbyDad03@21:1/5 to Leon on Fri Dec 23 11:55:20 2022
    On Friday, December 23, 2022 at 1:03:13 PM UTC-5, Leon wrote:
    On 12/22/2022 6:56 PM, DerbyDad03 wrote:
    On Thursday, December 22, 2022 at 9:11:20 AM UTC-5, gros...@gmail.com wrote:
    On Thursday, December 22, 2022 at 1:47:51 AM UTC-5, DerbyDad03 wrote:

    There’s no mention of removing the fence and using the tool
    in the middle of a wide board. In fact, they specifically mention
    what the tool is “capable” of doing. 1.75” off the edge.

    I might just give them a call and get a direct answer. Might. ;-)
    Seems like removing the fence and indexing off a board or straight edge clamp would be a "normal" application of such a tool... No?

    I tend to agree, but they don't mention it or show it, yet they specifically mention
    the 'capability' being "putting a mortise at the center of a 3.5” board or 1.75” off
    the edge of your work piece." One could easily read that as the *limit* of the tool's
    capability.

    Maybe their ad writers either don't know or didn't think ahead far enough to word it
    differently. Something like this makes it much clearer and makes the tool sound more
    versatile. Assuming it's true. ;-)

    "With the included fence, the Pocket Mill Pro is capable of putting a mortise at the
    center of a 3.5” board or 1.75” off the edge of your work piece. Removing the fence
    allows the user to put a mortise at any location they choose."
    Ok, I got a reply, you have to remove a part and attach a part. The
    part to attach has not yet been fully developed and will apparently be
    an add-on accessory. If the accessories are as expensive as this
    incomplete jig you might as well go for the Domino.

    Well, I sure feel vindicated. Yay me! ;-)

    So at this time, it's capabilities are indeed limited to the 3.5" spec noted.

    Granted, any one of us could probably make it work for wider panels, even without the "we haven't figured out how to make" accessory they plan on selling. Still, that video is a bit misleading. They should have used a 3.5" panel and then there wouldn't be any question as to what the tool is capable of doing. The video and the text would match.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From krw@notreal.com@21:1/5 to teamarrows@eznet.net on Sat Dec 24 10:58:14 2022
    On Fri, 23 Dec 2022 11:55:20 -0800 (PST), DerbyDad03
    <teamarrows@eznet.net> wrote:

    On Friday, December 23, 2022 at 1:03:13 PM UTC-5, Leon wrote:
    On 12/22/2022 6:56 PM, DerbyDad03 wrote:
    On Thursday, December 22, 2022 at 9:11:20 AM UTC-5, gros...@gmail.com wrote:
    On Thursday, December 22, 2022 at 1:47:51 AM UTC-5, DerbyDad03 wrote:

    Theres no mention of removing the fence and using the tool
    in the middle of a wide board. In fact, they specifically mention
    what the tool is capable of doing. 1.75 off the edge.

    I might just give them a call and get a direct answer. Might. ;-)
    Seems like removing the fence and indexing off a board or straight edge clamp would be a "normal" application of such a tool... No?

    I tend to agree, but they don't mention it or show it, yet they specifically mention
    the 'capability' being "putting a mortise at the center of a 3.5 board or 1.75 off
    the edge of your work piece." One could easily read that as the *limit* of the tool's
    capability.

    Maybe their ad writers either don't know or didn't think ahead far enough to word it
    differently. Something like this makes it much clearer and makes the tool sound more
    versatile. Assuming it's true. ;-)

    "With the included fence, the Pocket Mill Pro is capable of putting a mortise at the
    center of a 3.5 board or 1.75 off the edge of your work piece. Removing the fence
    allows the user to put a mortise at any location they choose."
    Ok, I got a reply, you have to remove a part and attach a part. The
    part to attach has not yet been fully developed and will apparently be
    an add-on accessory. If the accessories are as expensive as this
    incomplete jig you might as well go for the Domino.

    Well, I sure feel vindicated. Yay me! ;-)

    So at this time, it's capabilities are indeed limited to the 3.5" spec noted.

    Granted, any one of us could probably make it work for wider panels, even >without the "we haven't figured out how to make" accessory they plan on >selling. Still, that video is a bit misleading. They should have used a 3.5" >panel and then there wouldn't be any question as to what the tool is capable >of doing. The video and the text would match.

    Isn't that how business works? Marketeers show it as a floor wax and
    desert topping. Then they pass it off to the engineers to figure out
    how and the lawyers to make sure the CYA gets written to cover them in
    court.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Leon@21:1/5 to All on Sat Dec 24 10:12:14 2022
    On 12/23/2022 1:55 PM, DerbyDad03 wrote:
    On Friday, December 23, 2022 at 1:03:13 PM UTC-5, Leon wrote:
    On 12/22/2022 6:56 PM, DerbyDad03 wrote:
    On Thursday, December 22, 2022 at 9:11:20 AM UTC-5, gros...@gmail.com wrote:
    On Thursday, December 22, 2022 at 1:47:51 AM UTC-5, DerbyDad03 wrote:

    There’s no mention of removing the fence and using the tool
    in the middle of a wide board. In fact, they specifically mention
    what the tool is “capable” of doing. 1.75” off the edge.

    I might just give them a call and get a direct answer. Might. ;-)
    Seems like removing the fence and indexing off a board or straight edge clamp would be a "normal" application of such a tool... No?

    I tend to agree, but they don't mention it or show it, yet they specifically mention
    the 'capability' being "putting a mortise at the center of a 3.5” board or 1.75” off
    the edge of your work piece." One could easily read that as the *limit* of the tool's
    capability.

    Maybe their ad writers either don't know or didn't think ahead far enough to word it
    differently. Something like this makes it much clearer and makes the tool sound more
    versatile. Assuming it's true. ;-)

    "With the included fence, the Pocket Mill Pro is capable of putting a mortise at the
    center of a 3.5” board or 1.75” off the edge of your work piece. Removing the fence
    allows the user to put a mortise at any location they choose."
    Ok, I got a reply, you have to remove a part and attach a part. The
    part to attach has not yet been fully developed and will apparently be
    an add-on accessory. If the accessories are as expensive as this
    incomplete jig you might as well go for the Domino.

    Well, I sure feel vindicated. Yay me! ;-)

    So at this time, it's capabilities are indeed limited to the 3.5" spec noted.

    Granted, any one of us could probably make it work for wider panels, even without the "we haven't figured out how to make" accessory they plan on selling. Still, that video is a bit misleading. They should have used a 3.5" panel and then there wouldn't be any question as to what the tool is capable of doing. The video and the text would match.

    Agree Totally. This and many of the WoodPeckers tools seem half baked.
    Woodpeckers does not seem to place much importance on a zero
    clearance sacrificial fence on their products.

    I bought their "Exact 90" miter gauge. Nice product. but the flip stop
    that references the scale for the length of cut moves when it is flipped
    down after placing. The flip stop is mounted on a screw that screws in
    and out as you rotate the flip. Not much but it moves approximately
    1/4 of 1/32", and or 1/128". This would not normally be a problem, but
    when a sacrificial fence is used the flip stop does not sit in a usable location on the scale to be able to understand where it is actually
    being placed. So you have to flip the stop up so that it references
    the more legible part of the scale. And if you tighten it at that spot,
    the stop moves 1/128" when you flip it down to use it.
    Woodpeckers did not think that was a problem but did change the flip
    stop on another tool that eliminates this issue.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)