• 100 Grit Sandpaper For DIY "Track Saw"?

    From DerbyDad03@21:1/5 to All on Fri Mar 25 20:47:05 2022
    We all know about the DIY saw guide using a strip of hardwood glued
    to plywood which is then cut with a circular saw. I've always held mine
    down with spring clamps.

    I saw segment on TV where the guy used spray adhesive to secure sheets
    of 100 grit sandpaper to the bottom to eliminate the need for clamps.

    It seemed to work, but his guide was only 4' long. Do you guys see any
    issues with that method, specifically on an 8' guide?

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Leon@21:1/5 to All on Sat Mar 26 16:42:35 2022
    On 3/25/2022 10:47 PM, DerbyDad03 wrote:
    We all know about the DIY saw guide using a strip of hardwood glued
    to plywood which is then cut with a circular saw. I've always held mine
    down with spring clamps.

    I saw segment on TV where the guy used spray adhesive to secure sheets
    of 100 grit sandpaper to the bottom to eliminate the need for clamps.

    It seemed to work, but his guide was only 4' long. Do you guys see any
    issues with that method, specifically on an 8' guide?


    Other than scratching the surface of what you are cutting, I don't see a problem.

    The high friction rubber tape on the bottom of the name brand track saw
    tracks is a consumable item and available. That tape does not scratch a finished/varnished surface, or laminate surface etc.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Sonny@21:1/5 to All on Sat Mar 26 16:32:16 2022
    I would think spraying glue and laying sand paper is more time consuming than simply using a couple of clamps.... for my needed degree of accuracy, anyway. I often consider or make allowance for some not-so-perfect of cut and have the jointers to
    clean up any mis-cuts. Even when using the table saw, I sometimes make allowance for cleaning a cut edge (saw marks) with the jointers.

    Sonny

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From DerbyDad03@21:1/5 to Leon on Sun Mar 27 07:26:02 2022
    On Saturday, March 26, 2022 at 5:42:44 PM UTC-4, Leon wrote:
    On 3/25/2022 10:47 PM, DerbyDad03 wrote:
    We all know about the DIY saw guide using a strip of hardwood glued
    to plywood which is then cut with a circular saw. I've always held mine down with spring clamps.

    I saw segment on TV where the guy used spray adhesive to secure sheets
    of 100 grit sandpaper to the bottom to eliminate the need for clamps.

    It seemed to work, but his guide was only 4' long. Do you guys see any issues with that method, specifically on an 8' guide?
    Other than scratching the surface of what you are cutting, I don't see a problem.

    That was my first thought too. That, and the loading it into my van when
    I take it on the road. Scratching other things is possible.


    The high friction rubber tape on the bottom of the name brand track saw tracks is a consumable item and available. That tape does not scratch a finished/varnished surface, or laminate surface etc.

    Do you have a source to offer? Obviously it needs to stick to wood, although
    a finish could be applied first.

    I need to make a new guide, so I'm considering something like this. The 100 grit sand paper method doesn't thrill me.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From DerbyDad03@21:1/5 to Sonny on Sun Mar 27 07:26:19 2022
    On Saturday, March 26, 2022 at 7:32:18 PM UTC-4, Sonny wrote:
    I would think spraying glue and laying sand paper is more time consuming than simply using a couple of clamps....

    Well, the first few times, sure. Eventually the payback period expires.

    or my needed degree of accuracy, anyway. I often consider or make allowance for some not-so-perfect
    of cut and have the jointers to clean up any mis-cuts. Even when using the table saw, I sometimes make
    allowance for cleaning a cut edge (saw marks) with the jointers.

    At home, I do the same, except for the jointer steps. I don't have a jointer.

    While "on the road" I don't have access to my other tools, so the saw guide cut is often the
    finish cut.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From DerbyDad03@21:1/5 to Leon on Sun Mar 27 12:12:38 2022
    On Sunday, March 27, 2022 at 2:52:27 PM UTC-4, Leon wrote:
    On 3/27/2022 9:26 AM, DerbyDad03 wrote:
    On Saturday, March 26, 2022 at 5:42:44 PM UTC-4, Leon wrote:
    On 3/25/2022 10:47 PM, DerbyDad03 wrote:
    We all know about the DIY saw guide using a strip of hardwood glued
    to plywood which is then cut with a circular saw. I've always held mine >>> down with spring clamps.

    I saw segment on TV where the guy used spray adhesive to secure sheets >>> of 100 grit sandpaper to the bottom to eliminate the need for clamps.

    It seemed to work, but his guide was only 4' long. Do you guys see any >>> issues with that method, specifically on an 8' guide?
    Other than scratching the surface of what you are cutting, I don't see a >> problem.

    That was my first thought too. That, and the loading it into my van when
    I take it on the road. Scratching other things is possible.


    The high friction rubber tape on the bottom of the name brand track saw
    tracks is a consumable item and available. That tape does not scratch a
    finished/varnished surface, or laminate surface etc.

    Do you have a source to offer? Obviously it needs to stick to wood, although
    a finish could be applied first.

    I need to make a new guide, so I'm considering something like this. The 100 grit sand paper method doesn't thrill me.
    Yes! Woodcraft sells the Festool bottom black tape. You can find The
    Festool brand and the Makita brand tape on Amazon.


    Here are a few, just make sure it is not electrical tape at this link.

    https://www.amazon.com/s?k=tracksaw+friction+tape&crid=2PEW3NGX6XTBQ&sprefix=track+saw+friction+tape%2Caps%2C74&ref=nb_sb_noss_1

    Thanks.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Leon@21:1/5 to All on Sun Mar 27 13:52:17 2022
    On 3/27/2022 9:26 AM, DerbyDad03 wrote:
    On Saturday, March 26, 2022 at 5:42:44 PM UTC-4, Leon wrote:
    On 3/25/2022 10:47 PM, DerbyDad03 wrote:
    We all know about the DIY saw guide using a strip of hardwood glued
    to plywood which is then cut with a circular saw. I've always held mine
    down with spring clamps.

    I saw segment on TV where the guy used spray adhesive to secure sheets
    of 100 grit sandpaper to the bottom to eliminate the need for clamps.

    It seemed to work, but his guide was only 4' long. Do you guys see any
    issues with that method, specifically on an 8' guide?
    Other than scratching the surface of what you are cutting, I don't see a
    problem.

    That was my first thought too. That, and the loading it into my van when
    I take it on the road. Scratching other things is possible.


    The high friction rubber tape on the bottom of the name brand track saw
    tracks is a consumable item and available. That tape does not scratch a
    finished/varnished surface, or laminate surface etc.

    Do you have a source to offer? Obviously it needs to stick to wood, although a finish could be applied first.

    I need to make a new guide, so I'm considering something like this. The 100 grit sand paper method doesn't thrill me.

    Yes! Woodcraft sells the Festool bottom black tape. You can find The
    Festool brand and the Makita brand tape on Amazon.


    Here are a few, just make sure it is not electrical tape at this link.

    https://www.amazon.com/s?k=tracksaw+friction+tape&crid=2PEW3NGX6XTBQ&sprefix=track+saw+friction+tape%2Caps%2C74&ref=nb_sb_noss_1

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)