So far this year a kitchen remodel in the winter and early spring. A
Murphy bed and twin tower storage cabinets to match the bed and not a
Pantry Hutch.
This is the drawing.
https://www.flickr.com/photos/lcb11211/51487087793/in/dateposted/
This will be constructed of 3/4" MDO for the cabinet carcasses and
adjustable shelves.
Poplar for all of the solid wood, except for Maple of the tops of the
bottom and top cabinets.
Drawers will have HD full extension drawer slides, 8 adjustable feet for leveling, and 6 Blum Euro hinges for the doors.
Door and drawer outer center panels will be 1/2" Baltic birch and the
drawers will be 1/2" Baltic birch for the all 4 sides and the bottoms. Rabbets for the drawer corner joints reinforced by Domino tenons.
The customer will retrieve and take back to San Antonio, TX, spray
paint the poplar and MOD parts. Clear coat the maple sections and
reassemble. The customer was a long time participant in this group. He
often passed along very detailed directions of how to spray paint.
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
I paid close attention when cutting up the $420 worth of MDO. That part
is done. I just finished printing optomized layouts for cutting up the
120 linear feet of 1x8 poplar and hard maple.
Thoughts?
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote:
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote:
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
On Friday, September 17, 2021 at 2:50:39 PM UTC-4, Leon wrote:
So far this year a kitchen remodel in the winter and early spring. A
Murphy bed and twin tower storage cabinets to match the bed and not a
Pantry Hutch.
This is the drawing.
https://www.flickr.com/photos/lcb11211/51487087793/in/dateposted/
This will be constructed of 3/4" MDO for the cabinet carcasses and
adjustable shelves.
Poplar for all of the solid wood, except for Maple of the tops of the
bottom and top cabinets.
Drawers will have HD full extension drawer slides, 8 adjustable feet for
leveling, and 6 Blum Euro hinges for the doors.
Door and drawer outer center panels will be 1/2" Baltic birch and the
drawers will be 1/2" Baltic birch for the all 4 sides and the bottoms.
Rabbets for the drawer corner joints reinforced by Domino tenons.
The customer will retrieve and take back to San Antonio, TX, spray
paint the poplar and MOD parts. Clear coat the maple sections and
reassemble. The customer was a long time participant in this group. He
often passed along very detailed directions of how to spray paint.
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
I paid close attention when cutting up the $420 worth of MDO. That part
is done. I just finished printing optomized layouts for cutting up the
120 linear feet of 1x8 poplar and hard maple.
Thoughts?
Thoughts?
My thought is that you should make two. The first one can be for practice. When it's done, give it to me at no charge since it's just a prototype.
Thoughts?
On Fri, 17 Sep 2021 16:00:30 -0700 (PDT), "russellseaton1@yahoo.com" <ritzannaseaton@gmail.com> wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote:
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
Thoughts? Where do you find MDO?
Oh, and it's going to be another Leon special, no doubt.
On 9/17/2021 6:00 PM, russell...@yahoo.com wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote:
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
Finishing does not bother me so much except for the time it adds to
complete a project. I almost always prefinish inside edges and closed
in panels prior to glue up. 3 coats of a gel varnish. Then after the
glue up 3 coats after sanding. That can easily add 2~8 days to the
process depending on the humidity.
And gel varnishes do not build quickly so they are thin. Not for
children's furniture.
Because this finish basically helps to prevent discoloration of the wood
and that is about it I am considering switching to Rubio Monocoat
finish. It too is a thin finish but it is 1 coat, fast dry, and applied
with either a white Scotch Brite pad or poured on a tiny bit at a time
and spread with a card scraper.
Comes in about 40~50 shades including pure/natural. And it is pricey.
But when time is money I think it is a wash.
Apparently a scratch is easily repaired, sand, and reapply 1 coat. No
lap marks.
On 9/17/2021 9:28 PM, krw@notreal.com wrote:
On Fri, 17 Sep 2021 16:00:30 -0700 (PDT), "russellseaton1@yahoo.com"
<ritzannaseaton@gmail.com> wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote:
Since I am not painting, staining, or applying a finishing for any part >>>> of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
Thoughts? Where do you find MDO?
I get it in Houston at either Clark's Hardwood Lumber or Hardwood
Products. At the moment Hardwood Products is out of stock and has no
idea when that will change. I suspect it may be available form any of
the local materials suppliers for the trades. A local lumber yard may
have it. The big box store "might" be able to order it for you.
Oh, and it's going to be another Leon special, no doubt.
Not totally my design, Nailshooter and his wife had a lot of input as to >sizing. They have stayed with us on numerous occasions and she wanted a >custom built piece. It has some of my unique features but no curves...
Hummm.
On Sat, 18 Sep 2021 09:23:03 -0500, Leon <lcb11211@swbelldotnet>
wrote:
On 9/17/2021 9:28 PM, k...@notreal.com wrote:
On Fri, 17 Sep 2021 16:00:30 -0700 (PDT), "russell...@yahoo.com"
<ritzann...@gmail.com> wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote:
Since I am not painting, staining, or applying a finishing for any part >>>> of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
Thoughts? Where do you find MDO?
I get it in Houston at either Clark's Hardwood Lumber or HardwoodThe BORG doesn't even recognize its existence and blue knows that it
Products. At the moment Hardwood Products is out of stock and has no
idea when that will change. I suspect it may be available form any of
the local materials suppliers for the trades. A local lumber yard may
have it. The big box store "might" be able to order it for you.
exists but will never stock it.
On Saturday, September 18, 2021 at 12:31:02 PM UTC-4, k...@notreal.com wrote: >> On Sat, 18 Sep 2021 09:23:03 -0500, Leon <lcb11211@swbelldotnet>
wrote:
On 9/17/2021 9:28 PM, k...@notreal.com wrote:The BORG doesn't even recognize its existence and blue knows that it
On Fri, 17 Sep 2021 16:00:30 -0700 (PDT), "russell...@yahoo.com"
<ritzann...@gmail.com> wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote:
Since I am not painting, staining, or applying a finishing for any part >> >>>> of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
Thoughts? Where do you find MDO?
I get it in Houston at either Clark's Hardwood Lumber or Hardwood
Products. At the moment Hardwood Products is out of stock and has no
idea when that will change. I suspect it may be available form any of
the local materials suppliers for the trades. A local lumber yard may
have it. The big box store "might" be able to order it for you.
exists but will never stock it.
Lowes carries 1/2 MDO. At least 50 sheets available locally.
I bought some a few weeks ago. I really only needed sanded ply but
the nice flat and slightly thicker MDO was a few bucks *cheaper* per
sheet than the ugly twisted sanded ply.
Can't find 3/4" though. Will try a lumber yard if I ever need any.
On Sat, 18 Sep 2021 12:03:54 -0700 (PDT), DerbyDad03
<teama...@eznet.net> wrote:
On Saturday, September 18, 2021 at 12:31:02 PM UTC-4, k...@notreal.com wrote:
On Sat, 18 Sep 2021 09:23:03 -0500, Leon <lcb11211@swbelldotnet>
wrote:
On 9/17/2021 9:28 PM, k...@notreal.com wrote:The BORG doesn't even recognize its existence and blue knows that it
On Fri, 17 Sep 2021 16:00:30 -0700 (PDT), "russell...@yahoo.com"
<ritzann...@gmail.com> wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote:
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
Thoughts? Where do you find MDO?
I get it in Houston at either Clark's Hardwood Lumber or Hardwood
Products. At the moment Hardwood Products is out of stock and has no
idea when that will change. I suspect it may be available form any of
the local materials suppliers for the trades. A local lumber yard may
have it. The big box store "might" be able to order it for you.
exists but will never stock it.
Lowes carries 1/2 MDO. At least 50 sheets available locally.Not here, in any stores in the metro area, or at least their web site
doesn't point to any.
I bought some a few weeks ago. I really only needed sanded ply butThe BORG did have some decent looking sanded ply. I just looked at
the nice flat and slightly thicker MDO was a few bucks *cheaper* per
sheet than the ugly twisted sanded ply.
the Lowes site and it appears plywood prices have come down. $40 for
3/4" sanded SYP and $60 for sanded poplar.
Can't find 3/4" though. Will try a lumber yard if I ever need any.
I'd love to find some. I've been using MDF or melamine (same thing)
where flat mattered.
On Saturday, September 18, 2021 at 3:25:31 PM UTC-4, k...@notreal.com wrote:
On Sat, 18 Sep 2021 12:03:54 -0700 (PDT), DerbyDad03
<teama...@eznet.net> wrote:
On Saturday, September 18, 2021 at 12:31:02 PM UTC-4, k...@notreal.com wrote:Not here, in any stores in the metro area, or at least their web site
On Sat, 18 Sep 2021 09:23:03 -0500, Leon <lcb11211@swbelldotnet>
wrote:
On 9/17/2021 9:28 PM, k...@notreal.com wrote:The BORG doesn't even recognize its existence and blue knows that it
On Fri, 17 Sep 2021 16:00:30 -0700 (PDT), "russell...@yahoo.com"
<ritzann...@gmail.com> wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote:
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
Thoughts? Where do you find MDO?
I get it in Houston at either Clark's Hardwood Lumber or Hardwood
Products. At the moment Hardwood Products is out of stock and has no >>>>> idea when that will change. I suspect it may be available form any of >>>>> the local materials suppliers for the trades. A local lumber yard may >>>>> have it. The big box store "might" be able to order it for you.
exists but will never stock it.
Lowes carries 1/2 MDO. At least 50 sheets available locally.
doesn't point to any.
I bought some a few weeks ago. I really only needed sanded ply butThe BORG did have some decent looking sanded ply. I just looked at
the nice flat and slightly thicker MDO was a few bucks *cheaper* per
sheet than the ugly twisted sanded ply.
the Lowes site and it appears plywood prices have come down. $40 for
3/4" sanded SYP and $60 for sanded poplar.
I'd love to find some. I've been using MDF or melamine (same thing)
Can't find 3/4" though. Will try a lumber yard if I ever need any.
where flat mattered.
In what world is MDF and melamine the same thing?
On Saturday, September 18, 2021 at 12:31:02 PM UTC-4, k...@notreal.com wrote:
On Sat, 18 Sep 2021 09:23:03 -0500, Leon <lcb11211@swbelldotnet>
wrote:
On 9/17/2021 9:28 PM, k...@notreal.com wrote:The BORG doesn't even recognize its existence and blue knows that it
On Fri, 17 Sep 2021 16:00:30 -0700 (PDT), "russell...@yahoo.com"
<ritzann...@gmail.com> wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote:
Since I am not painting, staining, or applying a finishing for any part >>>>>> of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
Thoughts? Where do you find MDO?
I get it in Houston at either Clark's Hardwood Lumber or Hardwood
Products. At the moment Hardwood Products is out of stock and has no
idea when that will change. I suspect it may be available form any of
the local materials suppliers for the trades. A local lumber yard may
have it. The big box store "might" be able to order it for you.
exists but will never stock it.
Lowes carries 1/2 MDO. At least 50 sheets available locally.
I bought some a few weeks ago. I really only needed sanded ply but
the nice flat and slightly thicker MDO was a few bucks *cheaper* per
sheet than the ugly twisted sanded ply.
Can't find 3/4" though. Will try a lumber yard if I ever need any.
On Saturday, September 18, 2021 at 10:14:59 AM UTC-4, Leon wrote:
On 9/17/2021 6:00 PM, russell...@yahoo.com wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote:Finishing does not bother me so much except for the time it adds to
Since I am not painting, staining, or applying a finishing for any part >>>> of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part. >>>
complete a project. I almost always prefinish inside edges and closed
in panels prior to glue up. 3 coats of a gel varnish. Then after the
glue up 3 coats after sanding. That can easily add 2~8 days to the
process depending on the humidity.
And gel varnishes do not build quickly so they are thin. Not for
children's furniture.
Because this finish basically helps to prevent discoloration of the wood
and that is about it I am considering switching to Rubio Monocoat
finish. It too is a thin finish but it is 1 coat, fast dry, and applied
with either a white Scotch Brite pad or poured on a tiny bit at a time
and spread with a card scraper.
Comes in about 40~50 shades including pure/natural. And it is pricey.
But when time is money I think it is a wash.
Apparently a scratch is easily repaired, sand, and reapply 1 coat. No
lap marks.
But who will repair the scratch 3 years after delivery? Are you the service department also or will you hand the customer whatever finish is left over, assuming there is some?
(I had a guy repair some rusty gussets, etc. on my trailer. Small job, but I don't weld. Some welding, some priming, some painting. He billed me for
quart of black paint, the remainder of which he gave to me when I picked
up the the trailer. Now I have about 85% of a quart of flat black oil based paint that will probably never get used. I should have given it to him as a tip.)
On 9/18/2021 10:02 AM, DerbyDad03 wrote:
On Saturday, September 18, 2021 at 10:14:59 AM UTC-4, Leon wrote:
On 9/17/2021 6:00 PM, russell...@yahoo.com wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote:Finishing does not bother me so much except for the time it adds to
Since I am not painting, staining, or applying a finishing for any part >>>> of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
complete a project. I almost always prefinish inside edges and closed
in panels prior to glue up. 3 coats of a gel varnish. Then after the
glue up 3 coats after sanding. That can easily add 2~8 days to the
process depending on the humidity.
And gel varnishes do not build quickly so they are thin. Not for
children's furniture.
Because this finish basically helps to prevent discoloration of the wood >> and that is about it I am considering switching to Rubio Monocoat
finish. It too is a thin finish but it is 1 coat, fast dry, and applied
with either a white Scotch Brite pad or poured on a tiny bit at a time
and spread with a card scraper.
Comes in about 40~50 shades including pure/natural. And it is pricey.
But when time is money I think it is a wash.
Apparently a scratch is easily repaired, sand, and reapply 1 coat. No
lap marks.
But who will repair the scratch 3 years after delivery? Are you the service department also or will you hand the customer whatever finish is left over, assuming there is some?
Good question. But ask your self this question, with "ANY" other
finish, who will repair the scratch 3 years after delivery?
The customer can buy $10 sample bottles of the product and do the repair himself. With most any other finish that repair will be much more
detailed, even with shellac.
And until I have tested this product more I don't know if it will be
good for everything or just certain projects. Like any other finish.
(I had a guy repair some rusty gussets, etc. on my trailer. Small job, but I
don't weld. Some welding, some priming, some painting. He billed me for quart of black paint, the remainder of which he gave to me when I picked
up the the trailer. Now I have about 85% of a quart of flat black oil based paint that will probably never get used. I should have given it to him as a tip.)
On 9/18/2021 2:03 PM, DerbyDad03 wrote:
On Saturday, September 18, 2021 at 12:31:02 PM UTC-4, k...@notreal.com wrote:
On Sat, 18 Sep 2021 09:23:03 -0500, Leon <lcb11211@swbelldotnet>
wrote:
On 9/17/2021 9:28 PM, k...@notreal.com wrote:The BORG doesn't even recognize its existence and blue knows that it
On Fri, 17 Sep 2021 16:00:30 -0700 (PDT), "russell...@yahoo.com"
<ritzann...@gmail.com> wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote:
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
Thoughts? Where do you find MDO?
I get it in Houston at either Clark's Hardwood Lumber or Hardwood
Products. At the moment Hardwood Products is out of stock and has no
idea when that will change. I suspect it may be available form any of
the local materials suppliers for the trades. A local lumber yard may
have it. The big box store "might" be able to order it for you.
exists but will never stock it.
Lowes carries 1/2 MDO. At least 50 sheets available locally.
I bought some a few weeks ago. I really only needed sanded ply butAND the surface likes any kind of paint. Some wood veneer plywoods tend
the nice flat and slightly thicker MDO was a few bucks *cheaper* per
sheet than the ugly twisted sanded ply.
to de laminate with some water based finishes. And that is the primary
reason that I use MDO over wood veneer if I am going to paint.
On 9/18/2021 6:59 PM, DerbyDad03 wrote:
On Saturday, September 18, 2021 at 3:25:31 PM UTC-4, k...@notreal.com wrote: >>> On Sat, 18 Sep 2021 12:03:54 -0700 (PDT), DerbyDad03
<teama...@eznet.net> wrote:
On Saturday, September 18, 2021 at 12:31:02 PM UTC-4, k...@notreal.com wrote:Not here, in any stores in the metro area, or at least their web site
On Sat, 18 Sep 2021 09:23:03 -0500, Leon <lcb11211@swbelldotnet>
wrote:
On 9/17/2021 9:28 PM, k...@notreal.com wrote:The BORG doesn't even recognize its existence and blue knows that it >>>>> exists but will never stock it.
On Fri, 17 Sep 2021 16:00:30 -0700 (PDT), "russell...@yahoo.com" >>>>>>> <ritzann...@gmail.com> wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote: >>>>>>>>>
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
Thoughts? Where do you find MDO?
I get it in Houston at either Clark's Hardwood Lumber or Hardwood
Products. At the moment Hardwood Products is out of stock and has no >>>>>> idea when that will change. I suspect it may be available form any of >>>>>> the local materials suppliers for the trades. A local lumber yard may >>>>>> have it. The big box store "might" be able to order it for you.
Lowes carries 1/2 MDO. At least 50 sheets available locally.
doesn't point to any.
I bought some a few weeks ago. I really only needed sanded ply butThe BORG did have some decent looking sanded ply. I just looked at
the nice flat and slightly thicker MDO was a few bucks *cheaper* per
sheet than the ugly twisted sanded ply.
the Lowes site and it appears plywood prices have come down. $40 for
3/4" sanded SYP and $60 for sanded poplar.
I'd love to find some. I've been using MDF or melamine (same thing)
Can't find 3/4" though. Will try a lumber yard if I ever need any.
where flat mattered.
In what world is MDF and melamine the same thing?
Wondering the same. ;~) Maybe just for the flatness comparison.
On Sunday, September 19, 2021 at 10:05:52 AM UTC-4, Leon wrote:
On 9/18/2021 2:03 PM, DerbyDad03 wrote:
On Saturday, September 18, 2021 at 12:31:02 PM UTC-4, k...@notreal.com wrote:AND the surface likes any kind of paint. Some wood veneer plywoods tend
On Sat, 18 Sep 2021 09:23:03 -0500, Leon <lcb11211@swbelldotnet>
wrote:
On 9/17/2021 9:28 PM, k...@notreal.com wrote:The BORG doesn't even recognize its existence and blue knows that it
On Fri, 17 Sep 2021 16:00:30 -0700 (PDT), "russell...@yahoo.com"
<ritzann...@gmail.com> wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote:
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
Thoughts? Where do you find MDO?
I get it in Houston at either Clark's Hardwood Lumber or Hardwood
Products. At the moment Hardwood Products is out of stock and has no >>>>> idea when that will change. I suspect it may be available form any of >>>>> the local materials suppliers for the trades. A local lumber yard may >>>>> have it. The big box store "might" be able to order it for you.
exists but will never stock it.
Lowes carries 1/2 MDO. At least 50 sheets available locally.
I bought some a few weeks ago. I really only needed sanded ply but
the nice flat and slightly thicker MDO was a few bucks *cheaper* per
sheet than the ugly twisted sanded ply.
to de laminate with some water based finishes. And that is the primary
reason that I use MDO over wood veneer if I am going to paint.
That's good to know. I used 3/4 Poplar veneered plywood for my last big project. It took the Benjamin Moore Advance primer and paint really well.
I like that paint a lot, especially since I seriously hate to paint. It lays down
nice and smooth.
The ultra smooth surface of the MDO isn't a problem? What kind of primer & paint do you use?
When I used the 1/2" MDO, I hid the surface. It was for that platform project in my Honda Odyssey, so it got covered with carpet. As I mentioned, I never would have considered using MDO, but it was cheaper than the sanded ply
and flat, unlike the sanded ply.
It was a good introduction to MDO, even though I didn't actually "finish" it. I will consider using it in the future.
On Sunday, September 19, 2021 at 10:13:39 AM UTC-4, Leon wrote:
On 9/18/2021 10:02 AM, DerbyDad03 wrote:
On Saturday, September 18, 2021 at 10:14:59 AM UTC-4, Leon wrote:
On 9/17/2021 6:00 PM, russell...@yahoo.com wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote:Finishing does not bother me so much except for the time it adds to
Since I am not painting, staining, or applying a finishing for any part >>>>>> of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
complete a project. I almost always prefinish inside edges and closed
in panels prior to glue up. 3 coats of a gel varnish. Then after the
glue up 3 coats after sanding. That can easily add 2~8 days to the
process depending on the humidity.
And gel varnishes do not build quickly so they are thin. Not for
children's furniture.
Because this finish basically helps to prevent discoloration of the wood >>>> and that is about it I am considering switching to Rubio Monocoat
finish. It too is a thin finish but it is 1 coat, fast dry, and applied >>>> with either a white Scotch Brite pad or poured on a tiny bit at a time >>>> and spread with a card scraper.
Comes in about 40~50 shades including pure/natural. And it is pricey.
But when time is money I think it is a wash.
Apparently a scratch is easily repaired, sand, and reapply 1 coat. No
lap marks.
But who will repair the scratch 3 years after delivery? Are you the service >>> department also or will you hand the customer whatever finish is left over, >>> assuming there is some?
Good question. But ask your self this question, with "ANY" other
finish, who will repair the scratch 3 years after delivery?
Depends on the terms of the warranty/protection plan. At this very
moment I am looking at a brochure for the Platinum Protection Plan
offered by the Raymour & Flanigan furniture chain. That's their 5
year protection plan.
The column for Wood and Other Hard Surface Furniture has a checkbox
next to "Gouges or chips that penetrate the finish exposing the substrate." That box is checked.
The customer can buy $10 sample bottles of the product and do the repair
himself. With most any other finish that repair will be much more
detailed, even with shellac.
So, what I am hearing is that you aren't offering a 5 year Platinum Protection Plan. ;-)
On 9/19/2021 11:02 AM, DerbyDad03 wrote:
On Sunday, September 19, 2021 at 10:13:39 AM UTC-4, Leon wrote:
On 9/18/2021 10:02 AM, DerbyDad03 wrote:
On Saturday, September 18, 2021 at 10:14:59 AM UTC-4, Leon wrote:
On 9/17/2021 6:00 PM, russell...@yahoo.com wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote:Finishing does not bother me so much except for the time it adds to
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
complete a project. I almost always prefinish inside edges and closed >>>> in panels prior to glue up. 3 coats of a gel varnish. Then after the >>>> glue up 3 coats after sanding. That can easily add 2~8 days to the
process depending on the humidity.
And gel varnishes do not build quickly so they are thin. Not for
children's furniture.
Because this finish basically helps to prevent discoloration of the wood >>>> and that is about it I am considering switching to Rubio Monocoat
finish. It too is a thin finish but it is 1 coat, fast dry, and applied >>>> with either a white Scotch Brite pad or poured on a tiny bit at a time >>>> and spread with a card scraper.
Comes in about 40~50 shades including pure/natural. And it is pricey. >>>> But when time is money I think it is a wash.
Apparently a scratch is easily repaired, sand, and reapply 1 coat. No >>>> lap marks.
But who will repair the scratch 3 years after delivery? Are you the service
department also or will you hand the customer whatever finish is left over,
assuming there is some?
Good question. But ask your self this question, with "ANY" other
finish, who will repair the scratch 3 years after delivery?
Depends on the terms of the warranty/protection plan. At this very
moment I am looking at a brochure for the Platinum Protection Plan
offered by the Raymour & Flanigan furniture chain. That's their 5
year protection plan.
The column for Wood and Other Hard Surface Furniture has a checkbox
next to "Gouges or chips that penetrate the finish exposing the substrate." That box is checked.
The customer can buy $10 sample bottles of the product and do the repair >> himself. With most any other finish that repair will be much more
detailed, even with shellac.
So, what I am hearing is that you aren't offering a 5 year Platinum Protection Plan. ;-)No, I do not. And FWIW I have bought my last furniture warranty
protection plan. I have been stung for the last time.
So our plan covered just about everything. Pets knawing on the wooden
parts. And doing their thing on the leather, #1 and #2. I can throw up
on the leather. Stab a hole in the leather.
We later found out the hard way that sweat is not covered.
On 9/19/2021 11:13 AM, DerbyDad03 wrote:
On Sunday, September 19, 2021 at 10:05:52 AM UTC-4, Leon wrote:
On 9/18/2021 2:03 PM, DerbyDad03 wrote:
On Saturday, September 18, 2021 at 12:31:02 PM UTC-4, k...@notreal.com wrote:AND the surface likes any kind of paint. Some wood veneer plywoods tend
On Sat, 18 Sep 2021 09:23:03 -0500, Leon <lcb11211@swbelldotnet>
wrote:
On 9/17/2021 9:28 PM, k...@notreal.com wrote:The BORG doesn't even recognize its existence and blue knows that it >>>> exists but will never stock it.
On Fri, 17 Sep 2021 16:00:30 -0700 (PDT), "russell...@yahoo.com" >>>>>> <ritzann...@gmail.com> wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote: >>>>>>>>
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
Thoughts? Where do you find MDO?
I get it in Houston at either Clark's Hardwood Lumber or Hardwood
Products. At the moment Hardwood Products is out of stock and has no >>>>> idea when that will change. I suspect it may be available form any of >>>>> the local materials suppliers for the trades. A local lumber yard may >>>>> have it. The big box store "might" be able to order it for you.
Lowes carries 1/2 MDO. At least 50 sheets available locally.
I bought some a few weeks ago. I really only needed sanded ply but
the nice flat and slightly thicker MDO was a few bucks *cheaper* per
sheet than the ugly twisted sanded ply.
to de laminate with some water based finishes. And that is the primary
reason that I use MDO over wood veneer if I am going to paint.
That's good to know. I used 3/4 Poplar veneered plywood for my last big project. It took the Benjamin Moore Advance primer and paint really well.
I like that paint a lot, especially since I seriously hate to paint. It lays down
nice and smooth.
The ultra smooth surface of the MDO isn't a problem? What kind of primer & paint do you use?No Primer. So far I have painted all of my MDO pieces with General
Finishes Milk Paint. The recently finished Murphy bed was painted with
a Basil green milk paint.
I did scuff the surface with 180 grit paper.
On Monday, September 20, 2021 at 9:39:33 AM UTC-4, Leon wrote:
On 9/19/2021 11:13 AM, DerbyDad03 wrote:Don't tell my wife. My next project is a bookcase for her.
On Sunday, September 19, 2021 at 10:05:52 AM UTC-4, Leon wrote:No Primer. So far I have painted all of my MDO pieces with General
On 9/18/2021 2:03 PM, DerbyDad03 wrote:
On Saturday, September 18, 2021 at 12:31:02 PM UTC-4, k...@notreal.com wrote:AND the surface likes any kind of paint. Some wood veneer plywoods tend >>>> to de laminate with some water based finishes. And that is the primary >>>> reason that I use MDO over wood veneer if I am going to paint.
On Sat, 18 Sep 2021 09:23:03 -0500, Leon <lcb11211@swbelldotnet>
wrote:
On 9/17/2021 9:28 PM, k...@notreal.com wrote:The BORG doesn't even recognize its existence and blue knows that it >>>>>> exists but will never stock it.
On Fri, 17 Sep 2021 16:00:30 -0700 (PDT), "russell...@yahoo.com" >>>>>>>> <ritzann...@gmail.com> wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote: >>>>>>>>>>
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
Thoughts? Where do you find MDO?
I get it in Houston at either Clark's Hardwood Lumber or Hardwood >>>>>>> Products. At the moment Hardwood Products is out of stock and has no >>>>>>> idea when that will change. I suspect it may be available form any of >>>>>>> the local materials suppliers for the trades. A local lumber yard may >>>>>>> have it. The big box store "might" be able to order it for you.
Lowes carries 1/2 MDO. At least 50 sheets available locally.
I bought some a few weeks ago. I really only needed sanded ply but
the nice flat and slightly thicker MDO was a few bucks *cheaper* per >>>>> sheet than the ugly twisted sanded ply.
That's good to know. I used 3/4 Poplar veneered plywood for my last big
project. It took the Benjamin Moore Advance primer and paint really well. >>> I like that paint a lot, especially since I seriously hate to paint. It lays down
nice and smooth.
The ultra smooth surface of the MDO isn't a problem? What kind of primer & >>> paint do you use?
Finishes Milk Paint. The recently finished Murphy bed was painted with
a Basil green milk paint.
While I may consider milk paint, I hate green. ;-)
Good to know.
I did scuff the surface with 180 grit paper.
On Monday, September 20, 2021 at 9:32:20 AM UTC-4, Leon wrote:
On 9/19/2021 11:02 AM, DerbyDad03 wrote:
On Sunday, September 19, 2021 at 10:13:39 AM UTC-4, Leon wrote:No, I do not. And FWIW I have bought my last furniture warranty
On 9/18/2021 10:02 AM, DerbyDad03 wrote:
On Saturday, September 18, 2021 at 10:14:59 AM UTC-4, Leon wrote:
On 9/17/2021 6:00 PM, russell...@yahoo.com wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote:Finishing does not bother me so much except for the time it adds to >>>>>> complete a project. I almost always prefinish inside edges and closed >>>>>> in panels prior to glue up. 3 coats of a gel varnish. Then after the >>>>>> glue up 3 coats after sanding. That can easily add 2~8 days to the >>>>>> process depending on the humidity.
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
And gel varnishes do not build quickly so they are thin. Not for
children's furniture.
Because this finish basically helps to prevent discoloration of the wood >>>>>> and that is about it I am considering switching to Rubio Monocoat
finish. It too is a thin finish but it is 1 coat, fast dry, and applied >>>>>> with either a white Scotch Brite pad or poured on a tiny bit at a time >>>>>> and spread with a card scraper.
Comes in about 40~50 shades including pure/natural. And it is pricey. >>>>>> But when time is money I think it is a wash.
Apparently a scratch is easily repaired, sand, and reapply 1 coat. No >>>>>> lap marks.
But who will repair the scratch 3 years after delivery? Are you the service
department also or will you hand the customer whatever finish is left over,
assuming there is some?
Good question. But ask your self this question, with "ANY" other
finish, who will repair the scratch 3 years after delivery?
Depends on the terms of the warranty/protection plan. At this very
moment I am looking at a brochure for the Platinum Protection Plan
offered by the Raymour & Flanigan furniture chain. That's their 5
year protection plan.
The column for Wood and Other Hard Surface Furniture has a checkbox
next to "Gouges or chips that penetrate the finish exposing the substrate." >>> That box is checked.
The customer can buy $10 sample bottles of the product and do the repair >>>> himself. With most any other finish that repair will be much more
detailed, even with shellac.
So, what I am hearing is that you aren't offering a 5 year Platinum
Protection Plan. ;-)
protection plan. I have been stung for the last time.
So our plan covered just about everything. Pets knawing on the wooden
parts. And doing their thing on the leather, #1 and #2. I can throw up
on the leather. Stab a hole in the leather.
We later found out the hard way that sweat is not covered.
You should have rented a cat to pee on your sweat stains before
you put in the claim.
On 9/20/2021 2:05 PM, DerbyDad03 wrote:
On Monday, September 20, 2021 at 9:32:20 AM UTC-4, Leon wrote:
On 9/19/2021 11:02 AM, DerbyDad03 wrote:
On Sunday, September 19, 2021 at 10:13:39 AM UTC-4, Leon wrote:No, I do not. And FWIW I have bought my last furniture warranty
On 9/18/2021 10:02 AM, DerbyDad03 wrote:
On Saturday, September 18, 2021 at 10:14:59 AM UTC-4, Leon wrote: >>>>>> On 9/17/2021 6:00 PM, russell...@yahoo.com wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote: >>>>>>>>Finishing does not bother me so much except for the time it adds to >>>>>> complete a project. I almost always prefinish inside edges and closed >>>>>> in panels prior to glue up. 3 coats of a gel varnish. Then after the >>>>>> glue up 3 coats after sanding. That can easily add 2~8 days to the >>>>>> process depending on the humidity.
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
And gel varnishes do not build quickly so they are thin. Not for >>>>>> children's furniture.
Because this finish basically helps to prevent discoloration of the wood
and that is about it I am considering switching to Rubio Monocoat >>>>>> finish. It too is a thin finish but it is 1 coat, fast dry, and applied
with either a white Scotch Brite pad or poured on a tiny bit at a time >>>>>> and spread with a card scraper.
Comes in about 40~50 shades including pure/natural. And it is pricey. >>>>>> But when time is money I think it is a wash.
Apparently a scratch is easily repaired, sand, and reapply 1 coat. No >>>>>> lap marks.
But who will repair the scratch 3 years after delivery? Are you the service
department also or will you hand the customer whatever finish is left over,
assuming there is some?
Good question. But ask your self this question, with "ANY" other
finish, who will repair the scratch 3 years after delivery?
Depends on the terms of the warranty/protection plan. At this very
moment I am looking at a brochure for the Platinum Protection Plan
offered by the Raymour & Flanigan furniture chain. That's their 5
year protection plan.
The column for Wood and Other Hard Surface Furniture has a checkbox
next to "Gouges or chips that penetrate the finish exposing the substrate."
That box is checked.
The customer can buy $10 sample bottles of the product and do the repair >>>> himself. With most any other finish that repair will be much more
detailed, even with shellac.
So, what I am hearing is that you aren't offering a 5 year Platinum
Protection Plan. ;-)
protection plan. I have been stung for the last time.
So our plan covered just about everything. Pets knawing on the wooden
parts. And doing their thing on the leather, #1 and #2. I can throw up
on the leather. Stab a hole in the leather.
We later found out the hard way that sweat is not covered.
You should have rented a cat to pee on your sweat stains before
you put in the claim.
So I called for warranty coverage and answered 20 questions. What would
you say caused the surface to discolor. Me, I don't know, maybe sweat.
Is that what you want us to put down as the cause? Sure, its a bodily
fluid, I don't really care what caused it.
Is that your final answer? Yes,
Pause, we are sorry but sweat is not covered.
I bought the furniture at a prominent store in Houston and the brand was Flexsteel. Not Cheap.
I read the manager the riot act and he took care of the problem.
On 9/20/2021 2:08 PM, DerbyDad03 wrote:
On Monday, September 20, 2021 at 9:39:33 AM UTC-4, Leon wrote:
On 9/19/2021 11:13 AM, DerbyDad03 wrote:Don't tell my wife. My next project is a bookcase for her.
On Sunday, September 19, 2021 at 10:05:52 AM UTC-4, Leon wrote:No Primer. So far I have painted all of my MDO pieces with General
On 9/18/2021 2:03 PM, DerbyDad03 wrote:
On Saturday, September 18, 2021 at 12:31:02 PM UTC-4, k...@notreal.com wrote:AND the surface likes any kind of paint. Some wood veneer plywoods tend >>>>> to de laminate with some water based finishes. And that is the primary >>>>> reason that I use MDO over wood veneer if I am going to paint.
On Sat, 18 Sep 2021 09:23:03 -0500, Leon <lcb11211@swbelldotnet> >>>>>>> wrote:
On 9/17/2021 9:28 PM, k...@notreal.com wrote:
On Fri, 17 Sep 2021 16:00:30 -0700 (PDT), "russell...@yahoo.com" >>>>>>>>> <ritzann...@gmail.com> wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote: >>>>>>>>>>>
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
Thoughts? Where do you find MDO?
I get it in Houston at either Clark's Hardwood Lumber or Hardwood >>>>>>>> Products. At the moment Hardwood Products is out of stock and has no >>>>>>>> idea when that will change. I suspect it may be available form any of >>>>>>>> the local materials suppliers for the trades. A local lumber yard may >>>>>>>> have it. The big box store "might" be able to order it for you. >>>>>>> The BORG doesn't even recognize its existence and blue knows that it >>>>>>> exists but will never stock it.
Lowes carries 1/2 MDO. At least 50 sheets available locally.
I bought some a few weeks ago. I really only needed sanded ply but >>>>>> the nice flat and slightly thicker MDO was a few bucks *cheaper* per >>>>>> sheet than the ugly twisted sanded ply.
That's good to know. I used 3/4 Poplar veneered plywood for my last big >>>> project. It took the Benjamin Moore Advance primer and paint really well. >>>> I like that paint a lot, especially since I seriously hate to paint. It lays down
nice and smooth.
The ultra smooth surface of the MDO isn't a problem? What kind of primer & >>>> paint do you use?
Finishes Milk Paint. The recently finished Murphy bed was painted with
a Basil green milk paint.
While I may consider milk paint, I hate green. ;-)
But does she like green? My wife pocked the color. Don't second guess >colors that your wife picks out. ;~)
The milk paints come in a load of "country colors".
On Monday, September 20, 2021 at 5:44:24 PM UTC-4, Leon wrote:
On 9/20/2021 2:05 PM, DerbyDad03 wrote:
On Monday, September 20, 2021 at 9:32:20 AM UTC-4, Leon wrote:So I called for warranty coverage and answered 20 questions. What would
On 9/19/2021 11:02 AM, DerbyDad03 wrote:
On Sunday, September 19, 2021 at 10:13:39 AM UTC-4, Leon wrote:No, I do not. And FWIW I have bought my last furniture warranty
On 9/18/2021 10:02 AM, DerbyDad03 wrote:
On Saturday, September 18, 2021 at 10:14:59 AM UTC-4, Leon wrote: >>>>>>>> On 9/17/2021 6:00 PM, russell...@yahoo.com wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote: >>>>>>>>>>Finishing does not bother me so much except for the time it adds to >>>>>>>> complete a project. I almost always prefinish inside edges and closed >>>>>>>> in panels prior to glue up. 3 coats of a gel varnish. Then after the >>>>>>>> glue up 3 coats after sanding. That can easily add 2~8 days to the >>>>>>>> process depending on the humidity.
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
And gel varnishes do not build quickly so they are thin. Not for >>>>>>>> children's furniture.
Because this finish basically helps to prevent discoloration of the wood
and that is about it I am considering switching to Rubio Monocoat >>>>>>>> finish. It too is a thin finish but it is 1 coat, fast dry, and applied
with either a white Scotch Brite pad or poured on a tiny bit at a time >>>>>>>> and spread with a card scraper.
Comes in about 40~50 shades including pure/natural. And it is pricey. >>>>>>>> But when time is money I think it is a wash.
Apparently a scratch is easily repaired, sand, and reapply 1 coat. No >>>>>>>> lap marks.
But who will repair the scratch 3 years after delivery? Are you the service
department also or will you hand the customer whatever finish is left over,
assuming there is some?
Good question. But ask your self this question, with "ANY" other
finish, who will repair the scratch 3 years after delivery?
Depends on the terms of the warranty/protection plan. At this very
moment I am looking at a brochure for the Platinum Protection Plan
offered by the Raymour & Flanigan furniture chain. That's their 5
year protection plan.
The column for Wood and Other Hard Surface Furniture has a checkbox
next to "Gouges or chips that penetrate the finish exposing the substrate."
That box is checked.
The customer can buy $10 sample bottles of the product and do the repair >>>>>> himself. With most any other finish that repair will be much more
detailed, even with shellac.
So, what I am hearing is that you aren't offering a 5 year Platinum
Protection Plan. ;-)
protection plan. I have been stung for the last time.
So our plan covered just about everything. Pets knawing on the wooden
parts. And doing their thing on the leather, #1 and #2. I can throw up >>>> on the leather. Stab a hole in the leather.
We later found out the hard way that sweat is not covered.
You should have rented a cat to pee on your sweat stains before
you put in the claim.
you say caused the surface to discolor. Me, I don't know, maybe sweat.
Is that what you want us to put down as the cause? Sure, its a bodily
fluid, I don't really care what caused it.
Is that your final answer? Yes,
Pause, we are sorry but sweat is not covered.
I bought the furniture at a prominent store in Houston and the brand was
Flexsteel. Not Cheap.
I read the manager the riot act and he took care of the problem.
I'm in the middle of similar issue right now, although mine is related to
an issue with the condition of my *not cheap* sectional upon arrival.
The one I waited 2 months to have delivered. (It's Covid, you know)
2 piece sectional, therefore 8 wooden legs. 5 of the 8 legs looked like
this at delivery:
https://i.imgur.com/UYYen3R.jpg
https://i.imgur.com/QDKQLHi.jpg
The repair guys shows up and based on the single picture that the delivery guy uploaded, the repair guy thought I had one minor scratch and thought
he could take it out to the truck and throw some stain on it. "That ain't happening, I want all new legs."
It's now 8 weeks later. They apparently lost the order for my legs and don't expect to see the second order for *at least* 6 more weeks. I told the rep that I could make a set of legs in one afternoon and be done with this fiasco.
"I'm sorry sir. We're sending you a $250 gift card for your trouble."
Great. Thanks. I probably can't even get a lamp at that store for $250.
On Mon, 20 Sep 2021 16:46:06 -0500, Leon <lcb11211@swbelldotnet>
wrote:
On 9/20/2021 2:08 PM, DerbyDad03 wrote:
On Monday, September 20, 2021 at 9:39:33 AM UTC-4, Leon wrote:
On 9/19/2021 11:13 AM, DerbyDad03 wrote:Don't tell my wife. My next project is a bookcase for her.
On Sunday, September 19, 2021 at 10:05:52 AM UTC-4, Leon wrote:No Primer. So far I have painted all of my MDO pieces with General
On 9/18/2021 2:03 PM, DerbyDad03 wrote:
On Saturday, September 18, 2021 at 12:31:02 PM UTC-4, k...@notreal.com wrote:AND the surface likes any kind of paint. Some wood veneer plywoods tend >>>>>> to de laminate with some water based finishes. And that is the primary >>>>>> reason that I use MDO over wood veneer if I am going to paint.
On Sat, 18 Sep 2021 09:23:03 -0500, Leon <lcb11211@swbelldotnet> >>>>>>>> wrote:
On 9/17/2021 9:28 PM, k...@notreal.com wrote:
On Fri, 17 Sep 2021 16:00:30 -0700 (PDT), "russell...@yahoo.com" >>>>>>>>>> <ritzann...@gmail.com> wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote: >>>>>>>>>>>>
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
Thoughts? Where do you find MDO?
I get it in Houston at either Clark's Hardwood Lumber or Hardwood >>>>>>>>> Products. At the moment Hardwood Products is out of stock and has no >>>>>>>>> idea when that will change. I suspect it may be available form any of >>>>>>>>> the local materials suppliers for the trades. A local lumber yard may >>>>>>>>> have it. The big box store "might" be able to order it for you. >>>>>>>> The BORG doesn't even recognize its existence and blue knows that it >>>>>>>> exists but will never stock it.
Lowes carries 1/2 MDO. At least 50 sheets available locally.
I bought some a few weeks ago. I really only needed sanded ply but >>>>>>> the nice flat and slightly thicker MDO was a few bucks *cheaper* per >>>>>>> sheet than the ugly twisted sanded ply.
That's good to know. I used 3/4 Poplar veneered plywood for my last big >>>>> project. It took the Benjamin Moore Advance primer and paint really well. >>>>> I like that paint a lot, especially since I seriously hate to paint. It lays down
nice and smooth.
The ultra smooth surface of the MDO isn't a problem? What kind of primer &
paint do you use?
Finishes Milk Paint. The recently finished Murphy bed was painted with >>>> a Basil green milk paint.
While I may consider milk paint, I hate green. ;-)
But does she like green? My wife pocked the color. Don't second guess
colors that your wife picks out. ;~)
I once had that plan, until it didn't work. She picked the paint for
our family room. She was out of the house paint day. I opened the
can and thought ("Pepto Bismol"). Well... She didn't much like it
either.
The milk paints come in a load of "country colors".
Not my favorites. Not enough saturation for my taste.
On 9/20/2021 7:22 PM, krw@notreal.com wrote:
On Mon, 20 Sep 2021 16:46:06 -0500, Leon <lcb11211@swbelldotnet>
wrote:
On 9/20/2021 2:08 PM, DerbyDad03 wrote:
On Monday, September 20, 2021 at 9:39:33 AM UTC-4, Leon wrote:
On 9/19/2021 11:13 AM, DerbyDad03 wrote:Don't tell my wife. My next project is a bookcase for her.
On Sunday, September 19, 2021 at 10:05:52 AM UTC-4, Leon wrote:No Primer. So far I have painted all of my MDO pieces with General
On 9/18/2021 2:03 PM, DerbyDad03 wrote:
On Saturday, September 18, 2021 at 12:31:02 PM UTC-4, k...@notreal.com wrote:AND the surface likes any kind of paint. Some wood veneer plywoods tend >>>>>>> to de laminate with some water based finishes. And that is the primary >>>>>>> reason that I use MDO over wood veneer if I am going to paint.
On Sat, 18 Sep 2021 09:23:03 -0500, Leon <lcb11211@swbelldotnet> >>>>>>>>> wrote:
On 9/17/2021 9:28 PM, k...@notreal.com wrote:
On Fri, 17 Sep 2021 16:00:30 -0700 (PDT), "russell...@yahoo.com" >>>>>>>>>>> <ritzann...@gmail.com> wrote:
On Friday, September 17, 2021 at 1:50:39 PM UTC-5, Leon wrote: >>>>>>>>>>>>>
Since I am not painting, staining, or applying a finishing for any part
of this job, the job should be fun.
True!!!!!! I like the mechanical constructing part. Not the finishing part.
Thoughts? Where do you find MDO?
I get it in Houston at either Clark's Hardwood Lumber or Hardwood >>>>>>>>>> Products. At the moment Hardwood Products is out of stock and has no >>>>>>>>>> idea when that will change. I suspect it may be available form any of
the local materials suppliers for the trades. A local lumber yard may
have it. The big box store "might" be able to order it for you. >>>>>>>>> The BORG doesn't even recognize its existence and blue knows that it >>>>>>>>> exists but will never stock it.
Lowes carries 1/2 MDO. At least 50 sheets available locally.
I bought some a few weeks ago. I really only needed sanded ply but >>>>>>>> the nice flat and slightly thicker MDO was a few bucks *cheaper* per >>>>>>>> sheet than the ugly twisted sanded ply.
That's good to know. I used 3/4 Poplar veneered plywood for my last big >>>>>> project. It took the Benjamin Moore Advance primer and paint really well.
I like that paint a lot, especially since I seriously hate to paint. It lays down
nice and smooth.
The ultra smooth surface of the MDO isn't a problem? What kind of primer &
paint do you use?
Finishes Milk Paint. The recently finished Murphy bed was painted with >>>>> a Basil green milk paint.
While I may consider milk paint, I hate green. ;-)
But does she like green? My wife pocked the color. Don't second guess
colors that your wife picks out. ;~)
I once had that plan, until it didn't work. She picked the paint for
our family room. She was out of the house paint day. I opened the
can and thought ("Pepto Bismol"). Well... She didn't much like it
either.
The milk paints come in a load of "country colors".
Not my favorites. Not enough saturation for my taste.
Define Saturation. General Finishes milk paints are heavy bodied and
quite opaque. One coat is almost enough over most any color.
| Sysop: | Keyop |
|---|---|
| Location: | Huddersfield, West Yorkshire, UK |
| Users: | 365 |
| Nodes: | 16 (3 / 13) |
| Uptime: | 05:12:42 |
| Calls: | 7,785 |
| Calls today: | 7 |
| Files: | 12,914 |
| Messages: | 5,750,432 |
