1. Forum
  2. Usenet
  3. REC.EQUESTRIAN

  • Bridle Nameplate Installation

    From Casey S.@21:1/5 to All on Wed May 26 19:56:45 2021
    Hello everyone!

    Does anyone here install their own bridle nameplates? I've been working on learning to do it well, but seem to have a hard time getting it down just right. At first, I had a hard time getting the rivets to set, but then found out I needed to use an anvil
    on concrete rather than my wooden workbench. Now I can set the rivets right, but they seem to come out looking funky or the nameplate gets scratched. On the rare occasion I've been able to have a professionally installed nameplate (I unfortunately no
    longer live near a tack shop that will do this), the rivets look nice and smooth, but mine don't. Does anyone have any tips for installing nameplates? I don't mind if they're not 100% perfect, but some of my rivets unfortunately look pretty bad.

    Thank you!
    Casey

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From John Hasler@21:1/5 to All on Thu May 27 09:54:17 2021
    What tools are you using to set the rivets? Generally each type of
    rivet needs a specially shaped rivet setter to get good looking results.
    --
    John Hasler
    john@dancinghorsehill.com
    Dancing Horse Hill
    Elmwood, WI USA

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Casey S.@21:1/5 to John Hasler on Thu May 27 09:02:23 2021
    On Thursday, May 27, 2021 at 10:08:38 AM UTC-5, John Hasler wrote:
    What tools are you using to set the rivets? Generally each type of
    rivet needs a specially shaped rivet setter to get good looking results.
    --
    John Hasler
    jo...@dancinghorsehill.com
    Dancing Horse Hill
    Elmwood, WI USA

    Thank you for your response!

    I have used a regular hammer, a rivet tool from Tandy Leather that is sold with some of their rivets (I didn't care for the results of using this, but it could've been that I didn't hold it steady enough or did something wrong), and a mallet also from
    Tandy Leather. So far, the hammer and mallet have been best, but the rivets still don't look smooth on top.

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From John Hasler@21:1/5 to All on Thu May 27 11:36:54 2021
    You need both a special rivet setting base and the correct rivet
    setter for the top to form the rivet to a consistent shape.

    Google "how to set rivets".
    --
    John Hasler
    john@dancinghorsehill.com
    Dancing Horse Hill
    Elmwood, WI USA

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Casey S.@21:1/5 to John Hasler on Thu May 27 10:37:03 2021
    On Thursday, May 27, 2021 at 12:08:49 PM UTC-5, John Hasler wrote:
    You need both a special rivet setting base and the correct rivet
    setter for the top to form the rivet to a consistent shape.

    Google "how to set rivets".
    --
    John Hasler
    jo...@dancinghorsehill.com
    Dancing Horse Hill
    Elmwood, WI USA

    The tool I used had both a base and a setter, but I'm not sure if I didn't hold it steady enough because it unfortunately created a "wrinkled" look to the rivets and put a dent in my nameplate. I have watched several videos that make it look so easy, but
    can't seem to figure out what I'm doing wrong!

    Thank you for your help! I will continue to look up more videos and maybe get an old piece of leather to practice setting rivets on for awhile!

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)