On 09/29/2017 01:50 PM, Chaotian Jing wrote:
On Fri, 2017-09-29 at 13:11 +0200, Matthias Brugger wrote:
On 09/22/2017 02:03 PM, Chaotian Jing wrote:
Change the comptiable for support of multi-platform
Add description for reg
Add description for source_cg
Add description for mediatek,latch-ck
Note that source_cg and mediatek,latch-ck are optional for some projects, >>> eg, MT2701 do not have source_cg, and MT2712 do not need
mediatek,latch-ck
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
---
Documentation/devicetree/bindings/mmc/mtk-sd.txt | 13 ++++++++++---
1 file changed, 10 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt
index 4182ea3..b934a29 100644
--- a/Documentation/devicetree/bindings/mmc/mtk-sd.txt
+++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt
@@ -7,10 +7,15 @@ This file documents differences between the core properties in mmc.txt
and the properties used by the msdc driver.
Required properties:
-- compatible: Should be "mediatek,mt8173-mmc","mediatek,mt8135-mmc"
+- compatible: value should be either of the following.
+ "mediatek,mt8135-mmc": for mmc host ip compatible with mt8135
+ "mediatek,mt8173-mmc": for mmc host ip compatible with mt8173
+ "mediatek,mt2701-mmc": for mmc host ip compatible with mt2701
+ "mediatek,mt2712-mmc": for mmc host ip compatible with mt2712
NAK, this has to be:
You have to add the fallback compatible ("mediatek,mt8135-mmc") to the binding
description as otherwise the driver does not get probed.
Regards,
Matthias
Thanks for your comments, will add the fallback compatible ("mediatek,mt8135-mmc") to the binding in this patch.
but, is possible to remove the fallback compatible at next patch ?
eg, following patches will modify the driver like below:
static const struct of_device_id msdc_of_ids[] = {
{ .compatible = "mediatek,mt8135-mmc", .data = &mt8135_compat},
{ .compatible = "mediatek,mt8173-mmc", .data = &mt8173_compat},
};
then, there is no probe issue and remove the fallback compatible.
Thx!
Right, if you have an explicit compatible in the driver, we don't need the fallback. But it doesn't hurt neither. As you like.
Regards,
Matthias
+- reg: physical base address of the controller and length
- interrupts: Should contain MSDC interrupt number
-- clocks: MSDC source clock, HCLK
-- clock-names: "source", "hclk"
+- clocks: MSDC source clock, HCLK, source_cg
+- clock-names: "source", "hclk", "source_cg"
- pinctrl-names: should be "default", "state_uhs"
- pinctrl-0: should contain default/high speed pin ctrl
- pinctrl-1: should contain uhs mode pin ctrl
@@ -30,6 +35,8 @@ Optional properties:
- mediatek,hs400-cmd-resp-sel-rising: HS400 command response sample selection
If present,HS400 command responses are sampled on rising edges.
If not present,HS400 command responses are sampled on falling edges.
+- mediatek,latch-ck: Some SoCs do not support enhance_rx, need set correct latch-ck to avoid data crc
+ error caused by stop clock(fifo full)
Examples:
mmc0: mmc@11230000 {
--- SoupGate-Win32 v1.05
* Origin: fsxNet Usenet Gateway (21:1/5)