• Bug#1065320: linux-image-6.1.0-18-amd64: 6.1.0-18 kernel enters ACPI Er

    From Lee Elliott@21:1/5 to All on Sat Mar 2 18:40:01 2024
    Package: src:linux
    Version: 6.1.76-1
    Severity: critical
    Justification: breaks the whole system
    X-Debbugs-Cc: leeejobsaccount@mail.co.uk

    Dear Maintainer,

    * What led up to the situation?

    Trying to boot the system with the 6.1.0-18 kernel

    * What exactly did you do (or not do) that was effective (or
    ineffective)?

    I tried adding 'boot_delay=1000' boot option to slow the console
    scroll rate, to enable better recording of the error messages.

    I tried rebooting the previous 6.1.0-17 kernel.

    * What was the outcome of this action?

    After adding the 'boot_delay=1000' option the boot process
    progressed no further than "Loading initial ramdisk ..."
    (left for several minutes - required power cycle).

    The system boots sucessfully on the previous 6.1.0-17 kernel

    * What outcome did you expect instead?

    I expected the system to successfully boot.

    * Additional observations

    This system also normally includes 'hpet=disable' and
    'acpi_enforce_resources=lax' boot options but removing these
    made no difference.

    Although I was not able to boot the system with the
    'boot_delay=1000' option and obtain clear photographs of the
    console output - the ones I've attached suffer from
    'overprinting' - it does seem clear that ACPI errors are
    being reported.

    There appear to be two distinct phases to this problem.
    Initially, ACPI seems to be reporting errors for "GPE", as
    shown in the first attached photograph, but after ~10 seconds
    or so, ACPI then switches to continuously reporting an error
    for PM_TIMER, as shown in the second attached photograph. At
    this point a power cycle is required.

    Purging and reinstalling the package made no difference. Atm,
    only three kernels are installed on this system but I have
    had more in the past as I normally compile my own kernels
    from the corresponding Debian source package. My own 6.1.76-1
    kernel also suffers from the same problem, whereas my own
    6.1.69-1 kernel boots and runs Ok.

    Comparing the kernel configs for 6.1.0-17 and 6.1.0-18
    showed just one functional change - an additional
    Compile-time checks and compiler option, which did not seem
    relevant to this problem.


    -- Package-specific info:
    ** Kernel log: boot messages should be attached

    ** Model information
    sys_vendor: ASUSTeK COMPUTER INC.
    product_name: E203NA
    product_version: 1.0
    chassis_vendor: ASUSTeK COMPUTER INC.
    chassis_version: 1.0
    bios_vendor: American Megatrends Inc.
    bios_version: E203NA.312
    board_vendor: ASUSTeK COMPUTER INC.
    board_name: E203NA
    board_version: 1.0

    ** Network interface configuration:
    *** /etc/network/interfaces:

    source /etc/network/interfaces.d/*

    auto lo
    iface lo inet loopback


    ** PCI devices:
    00:00.0 Host bridge [0600]: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series Host Bridge [8086:5af0] (rev 0b)
    Subsystem: ASUSTeK Computer Inc. Celeron N3350/Pentium N4200/Atom E3900 Series Host Bridge [1043:1980]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    IOMMU group: 1

    00:00.1 Signal processing controller [1180]: Intel Corporation Device [8086:5a8c] (rev 0b)
    Subsystem: ASUSTeK Computer Inc. Device [1043:1980]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
    Latency: 0
    Interrupt: pin B routed to IRQ 24
    IOMMU group: 1
    Region 0: Memory at 91310000 (64-bit, non-prefetchable) [size=32K]
    Capabilities: [d0] Power Management version 3
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [e0] Vendor Specific Information: Len=0c <?>
    Kernel driver in use: proc_thermal
    Kernel modules: processor_thermal_device_pci_legacy

    00:02.0 VGA compatible controller [0300]: Intel Corporation HD Graphics 500 [8086:5a85] (rev 0b) (prog-if 00 [VGA controller])
    Subsystem: ASUSTeK Computer Inc. HD Graphics 500 [1043:1980]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 125
    IOMMU group: 0
    Region 0: Memory at 90000000 (64-bit, non-prefetchable) [size=16M]
    Region 2: Memory at 80000000 (64-bit, prefetchable) [size=256M]
    Region 4: I/O ports at f000 [size=64]
    Expansion ROM at 000c0000 [virtual] [disabled] [size=128K]
    Capabilities: [40] Vendor Specific Information: Len=0c <?>
    Capabilities: [70] Express (v2) Root Complex Integrated Endpoint, MSI 00
    DevCap: MaxPayload 128 bytes, PhantFunc 0
    ExtTag- RBE+ FLReset+
    DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
    RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- FLReset-
    MaxPayload 128 bytes, MaxReadReq 128 bytes
    DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
    DevCap2: Completion Timeout: Not Supported, TimeoutDis- NROPrPrP- LTR-
    10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
    EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
    FRS-
    AtomicOpsCap: 32bit- 64bit- 128bitCAS-
    DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- 10BitTagReq- OBFF Disabled,
    AtomicOpsCtl: ReqEn-
    Capabilities: [ac] MSI: Enable+ Count=1/1 Maskable- 64bit-
    Address: fee00018 Data: 0000
    Capabilities: [d0] Power Management version 2
    Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [100 v1] Process Address Space ID (PASID)
    PASIDCap: Exec+ Priv-, Max PASID Width: 14
    PASIDCtl: Enable- Exec- Priv-
    Capabilities: [200 v1] Address Translation Service (ATS)
    ATSCap: Invalidate Queue Depth: 00
    ATSCtl: Enable-, Smallest Translation Unit: 00
    Capabilities: [300 v1] Page Request Interface (PRI)
    PRICtl: Enable- Reset-
    PRISta: RF- UPRGI- Stopped-
    Page Request Capacity: 00008000, Page Request Allocation: 00000000
    Kernel driver in use: i915
    Kernel modules: i915

    00:0e.0 Audio device [0403]: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series Audio Cluster [8086:5a98] (rev 0b)
    Subsystem: ASUSTeK Computer Inc. Celeron N3350/Pentium N4200/Atom E3900 Series Audio Cluster [1043:1980]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 127
    IOMMU group: 2
    Region 0: Memory at 91318000 (64-bit, non-prefetchable) [size=16K]
    Region 4: Memory at 91200000 (64-bit, non-prefetchable) [size=1M]
    Capabilities: [50] Power Management version 3
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D3 NoSoftRst+ PME-Enable+ DSel=0 DScale=0 PME-
    Capabilities: [80] Vendor Specific Information: Len=14 <?>
    Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
    Address: 00000000fee00398 Data: 0000
    Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
    DevCap: MaxPayload 128 bytes, PhantFunc 0
    ExtTag- RBE- FLReset+
    DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
    RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- FLReset-
    MaxPayload 128 bytes, MaxReadReq 512 bytes
    DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
    Kernel driver in use: snd_hda_intel
    Kernel modules: snd_hda_intel, snd_soc_skl, snd_sof_pci_intel_apl

    00:0f.0 Communication controller [0780]: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series Trusted Execution Engine [8086:5a9a] (rev 0b)
    Subsystem: ASUSTeK Computer Inc. Celeron N3350/Pentium N4200/Atom E3900 Series Trusted Execution Engine [1043:1980]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 126
    IOMMU group: 3
    Region 0: Memory at 91327000 (64-bit, non-prefetchable) [size=4K]
    Capabilities: [50] Power Management version 3
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
    Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+
    Address: 00000000fee00338 Data: 0000
    Capabilities: [a4] Vendor Specific Information: Len=14 <?>
    Kernel driver in use: mei_me
    Kernel modules: mei_me

    00:12.0 SATA controller [0106]: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series SATA AHCI Controller [8086:5ae3] (rev 0b) (prog-if 01 [AHCI 1.0])
    Subsystem: ASUSTeK Computer Inc. Celeron N3350/Pentium N4200/Atom E3900 Series SATA AHCI Controller [1043:1980]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 124
    IOMMU group: 4
    Region 0: Memory at 9131c000 (32-bit, non-prefetchable) [size=8K]
    Region 1: Memory at 91324000 (32-bit, non-prefetchable) [size=256]
    Region 2: I/O ports at f090 [size=8]
    Region 3: I/O ports at f080 [size=4]
    Region 4: I/O ports at f060 [size=32]
    Region 5: Memory at 91323000 (32-bit, non-prefetchable) [size=2K]
    Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
    Address: fee002f8 Data: 0000
    Capabilities: [70] Power Management version 3
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
    Status: D0 NoSoftRst+ PME-Enable+ DSel=0 DScale=0 PME-
    Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
    Kernel driver in use: ahci
    Kernel modules: ahci

    00:13.0 PCI bridge [0604]: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port A #2 [8086:5ad9] (rev fb) (prog-if 00 [Normal decode])
    Subsystem: ASUSTeK Computer Inc. Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port A [1043:1980]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Interrupt: pin B routed to IRQ 122
    IOMMU group: 5
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    I/O behind bridge: [disabled] [16-bit]
    Memory behind bridge: 91000000-911fffff [size=2M] [32-bit]
    Prefetchable memory behind bridge: [disabled] [64-bit]
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
    BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
    DevCap: MaxPayload 256 bytes, PhantFunc 0
    ExtTag- RBE+
    DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
    RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
    MaxPayload 256 bytes, MaxReadReq 128 bytes
    DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
    LnkCap: Port #4, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <4us
    ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
    LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes, Disabled- CommClk+
    ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
    LnkSta: Speed 2.5GT/s, Width x1
    TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
    SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
    Slot #3, PowerLimit 10W; Interlock- NoCompl+
    SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
    Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
    SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
    Changed: MRL- PresDet- LinkState+
    RootCap: CRSVisible-
    RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
    RootSta: PME ReqID 0000, PMEStatus- PMEPending-
    DevCap2: Completion Timeout: Range ABC, TimeoutDis+ NROPrPrP- LTR+
    10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
    EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
    FRS- LN System CLS Not Supported, TPHComp- ExtTPHComp- ARIFwd+
    AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
    DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR+ 10BitTagReq- OBFF Disabled, ARIFwd-
    AtomicOpsCtl: ReqEn- EgressBlck-
    LnkCap2: Supported Link Speeds: 2.5-5GT/s, Crosslink- Retimer- 2Retimers- DRS-
    LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
    Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
    Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot
    LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete- EqualizationPhase1-
    EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
    Retimer- 2Retimers- CrosslinkRes: unsupported
    Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
    Address: fee00218 Data: 0000
    Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Celeron N3350/Pentium N4200/Atom E3900 Series PCI Express Port A [1043:1980]
    Capabilities: [a0] Power Management version 3
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [100 v0] Null
    Capabilities: [140 v1] Access Control Services
    ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd- EgressCtrl- DirectTrans-
    ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
    Capabilities: [150 v0] Null
    Capabilities: [200 v0] Null
    Kernel driver in use: pcieport

    00:15.0 USB controller [0c03]: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series USB xHCI [8086:5aa8] (rev 0b) (prog-if 30 [XHCI])
    Subsystem: ASUSTeK Computer Inc. Celeron N3350/Pentium N4200/Atom E3900 Series USB xHCI [1043:201f]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 123
    IOMMU group: 6
    Region 0: Memory at 91300000 (64-bit, non-prefetchable) [size=64K]
    Capabilities: [70] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
    Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
    Address: 00000000fee002b8 Data: 0000
    Capabilities: [90] Vendor Specific Information: Len=14 <?>
    Kernel driver in use: xhci_hcd
    Kernel modules: xhci_pci

    00:17.0 Signal processing controller [1180]: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series I2C Controller #5 [8086:5ab4] (rev 0b)
    Subsystem: ASUSTeK Computer Inc. Celeron N3350/Pentium N4200/Atom E3900 Series I2C Controller [1043:1980]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 31
    IOMMU group: 7
    Region 0: Memory at 91322000 (64-bit, non-prefetchable) [size=4K]
    Region 2: Memory at 91321000 (64-bit, non-prefetchable) [size=4K]
    Capabilities: [80] Power Management version 3
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D3 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [90] Vendor Specific Information: Len=14 <?>
    Kernel driver in use: intel-lpss
    Kernel modules: intel_lpss_pci

    00:1c.0 SD Host controller [0805]: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series eMMC Controller [8086:5acc] (rev 0b) (prog-if 01)
    Subsystem: ASUSTeK Computer Inc. Celeron N3350/Pentium N4200/Atom E3900 Series eMMC Controller [1043:1980]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 39
    IOMMU group: 8
    Region 0: Memory at 91320000 (64-bit, non-prefetchable) [size=4K]
    Region 2: Memory at 9131f000 (64-bit, non-prefetchable) [size=4K]
    Capabilities: [80] Power Management version 3
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [90] Vendor Specific Information: Len=14 <?>
    Kernel driver in use: sdhci-pci
    Kernel modules: sdhci_pci

    00:1f.0 ISA bridge [0601]: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series Low Pin Count Interface [8086:5ae8] (rev 0b)
    Subsystem: ASUSTeK Computer Inc. Celeron N3350/Pentium N4200/Atom E3900 Series Low Pin Count Interface [1043:1980]
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    IOMMU group: 9
    Kernel driver in use: lpc_ich
    Kernel modules: lpc_ich

    00:1f.1 SMBus [0c05]: Intel Corporation Celeron N3350/Pentium N4200/Atom E3900 Series SMBus Controller [8086:5ad4] (rev 0b)
    Subsystem: ASUSTeK Computer Inc. Celeron N3350/Pentium N4200/Atom E3900 Series SMBus Controller [1043:1980]
    Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Interrupt: pin A routed to IRQ -2147483648
    IOMMU group: 9
    Region 0: Memory at 9131e000 (64-bit, non-prefetchable) [size=256]
    Region 4: I/O ports at f040 [size=32]
    Kernel driver in use: i801_smbus
    Kernel modules: i2c_i801

    01:00.0 Network controller [0280]: Qualcomm Atheros QCA9377 802.11ac Wireless Network Adapter [168c:0042] (rev 31)
    Subsystem: AzureWave QCA9377 802.11ac Wireless Network Adapter [1a3b:2a51]
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 128
    IOMMU group: 5
    Region 0: Memory at 91000000 (64-bit, non-prefetchable) [size=2M]
    Capabilities: [40] Power Management version 3
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [50] MSI: Enable+ Count=1/8 Maskable+ 64bit-
    Address: fee003b8 Data: 0000
    Masking: 000000fe Pending: 00000000
    Capabilities: [70] Express (v2) Endpoint, MSI 00
    DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us
    ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 10W
    DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq+
    RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
    MaxPayload 256 bytes, MaxReadReq 512 bytes
    DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
    LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <4us, L1 <64us
    ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
    LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes, Disabled- CommClk+
    ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
    LnkSta: Speed 2.5GT/s, Width x1
    TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
    DevCap2: Completion Timeout: Not Supported, TimeoutDis+ NROPrPrP- LTR+
    10BitTagComp- 10BitTagReq- OBFF Via message, ExtFmt- EETLPPrefix-
    EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
    FRS- TPHComp- ExtTPHComp-
    AtomicOpsCap: 32bit- 64bit- 128bitCAS-
    DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR+ 10BitTagReq- OBFF Disabled,
    AtomicOpsCtl: ReqEn-
    LnkCap2: Supported Link Speeds: 2.5GT/s, Crosslink- Retimer- 2Retimers- DRS-
    LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
    Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
    Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot
    LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
    EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
    Retimer- 2Retimers- CrosslinkRes: unsupported
    Capabilities: [100 v2] Advanced Error Reporting
    UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
    CESta: RxErr- BadTLP- BadDLLP+ Rollover+ Timeout+ AdvNonFatalErr-
    CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
    AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
    MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
    HeaderLog: 00000000 00000000 00000000 00000000
    Capabilities: [148 v1] Virtual Channel
    Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
    Arb: Fixed- WRR32- WRR64- WRR128-
    Ctrl: ArbSelect=Fixed
    Status: InProgress-
    VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
    Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
    Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
    Status: NegoPending- InProgress-
    Capabilities: [168 v1] Device Serial Number 00-00-00-00-00-00-00-00
    Capabilities: [178 v1] Latency Tolerance Reporting
    Max snoop latency: 3145728ns
    Max no snoop latency: 3145728ns
    Capabilities: [180 v1] L1 PM Substates
    L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
    PortCommonModeRestoreTime=50us PortTPowerOnTime=10us
    L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
    T_CommonMode=0us LTR1.2_Threshold=0ns
    L1SubCtl2: T_PwrOn=10us
    Kernel driver in use: ath10k_pci
    Kernel modules: ath10k_pci


    ** USB devices:
    Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
    Bus 001 Device 003: ID 04f2:b54b Chicony Electronics Co., Ltd USB2.0 VGA UVC WebCam
    Bus 001 Device 002: ID 13d3:3501 IMC Networks
    Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub


    -- System Information:
    Debian Release: 12.5
    APT prefers stable-updates
    APT policy: (500, 'stable-updates'), (500, 'stable-security'), (500, 'stable')
    Architecture: amd64 (x86_64)

    Kernel: Linux 6.1.0-17-amd64 (SMP w/2 CPU threads; PREEMPT)
    Locale: LANG=en_GB, LC_CTYPE=en_GB (charmap=ISO-8859-1), LANGUAGE=en_GB:en Shell: /bin/sh linked to /usr/bin/dash
    Init: systemd (via /run/systemd/system)
    LSM: AppArmor: enabled

    Versions of packages linux-image-6.1.0-18-amd64 depends on:
    ii initramfs-tools [linux-initramfs-tool] 0.142
    ii kmod 30+20221128-1
    ii linux-base 4.9

    Versions of packages linux-image-6.1.0-18-amd64 recommends:
    ii apparmor 3.0.8-3
    ii firmware-linux-free 20200122-1

    Versions of packages linux-image-6.1.0-18-amd64 suggests:
    pn debian-kernel-handbook <none>
    ii grub-efi-amd64 2.06-13+deb12u1
    pn linux-doc-6.1 <none>

    Versions of packages linux-image-6.1.0-18-amd64 is related to:
    ii firmware-amd-graphics 20230210-5
    ii firmware-atheros 20230210-5
    pn firmware-bnx2 <none>
    pn firmware-bnx2x <none>
    pn firmware-brcm80211 <none>
    pn firmware-cavium <none>
    pn firmware-intel-sound <none>
    pn firmware-intelwimax <none>
    pn firmware-ipw2x00 <none>
    pn firmware-ivtv <none>
    pn firmware-iwlwifi <none>
    pn firmware-libertas <none>
    ii firmware-linux-nonfree 20230210-5
    ii firmware-misc-nonfree 20230210-5
    pn firmware-myricom <none>
    pn firmware-netxen <none>
    pn firmware-qlogic <none>
    pn firmware-realtek <none>
    pn firmware-samsung <none>
    pn firmware-siano <none>
    pn firmware-ti-connectivity <none>
    pn xen-hypervisor <none>

    -- no debconf information

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Debian Bug Tracking System@21:1/5 to All on Thu Mar 7 22:40:01 2024
    Processing control commands:

    severity -1 serious
    Bug #1065320 [src:linux] linux-image-6.1.0-18-amd64: 6.1.0-18 kernel enters ACPI Error loop during boot & requires power cycle
    Severity set to 'serious' from 'critical'
    tags -1 + upstream fixed-upstream
    Bug #1065320 [src:linux] linux-image-6.1.0-18-amd64: 6.1.0-18 kernel enters ACPI Error loop during boot & requires power cycle
    Added tag(s) upstream and fixed-upstream.
    forwarded -1 https://lore.kernel.org/regressions/Zd2bsV8VsFJMlbFW@archie.me/ https://bugzilla.kernel.org/show_bug.cgi?id=218531
    Bug #1065320 [src:linux] linux-image-6.1.0-18-amd64: 6.1.0-18 kernel enters ACPI Error loop during boot & requires power cycle
    Set Bug forwarded-to-address to 'https://lore.kernel.org/regressions/Zd2bsV8VsFJMlbFW@archie.me/ https://bugzilla.kernel.org/show_bug.cgi?id=218531'.
    found -1 6.6.15-1
    Bug #1065320 [src:linux] linux-image-6.1.0-18-amd64: 6.1.0-18 kernel enters ACPI Error loop during boot & requires power cycle
    Marked as found in versions linux/6.6.15-1.
    found -1 6.7.4-1~exp1
    Bug #1065320 [src:linux] linux-image-6.1.0-18-amd64: 6.1.0-18 kernel enters ACPI Error loop during boot & requires power cycle
    Marked as found in versions linux/6.7.4-1~exp1.

    --
    1065320: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=1065320
    Debian Bug Tracking System
    Contact owner@bugs.debian.org with problems

    --- SoupGate-Win32 v1.05
    * Origin: fsxNet Usenet Gateway (21:1/5)
  • From Debian Bug Tracking System@21:1/5 to All on Tue Apr 16 00:00:01 2024
    This is a multi-part message in MIME format...

    Your message dated Mon, 15 Apr 2024 21:47:22 +0000
    with message-id <E1rwUAc-0068mp-3t@fasolo.debian.org>
    and subject line Bug#1065320: fixed in linux 6.1.85-1
    has caused the Debian Bug report #1065320,
    regarding linux-image-6.1.0-18-amd64: 6.1.0-18 kernel enters ACPI Error loop during boot & requires power cycle
    to be marked as done.

    This means that you claim that the problem has been dealt with.
    If this is not the case it is now your responsibility to reopen the
    Bug report if necessary, and/or fix the problem forthwith.

    (NB: If you are a system administrator and have no idea what this
    message is talking about, this may indicate a serious mail system misconfiguration somewhere. Please contact owner@bugs.debian.org
    immediately.)


    --
    1065320: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=1065320
    Debian Bug Tracking System
    Contact owner@bugs.debian.org with problems

    Received: (at submit) by bugs.debian.org; 2 Mar 2024 17:34:02 +0000 X-Spam-Checker-Version: SpamAssassin 3.4.6-bugs.debian.org_2005_01_02
    (2021-04-09) on buxtehude.debian.org
    X-Spam-Level:
    X-Spam-Status: No, score=-10.6 required=4.0 tests=BAYES_00,
    BODY_INCLUDES_PACKAGE,FOURLA,HAS_PACKAGE,KHOP_HELO_FCRDNS,RCVD_IN_PBL,
    RDNS_DYNAMIC,SPF_HELO_NONE,SPF_NEUTRAL,T_SCC_BODY_TEXT_LINE,
    XMAILER_REPORTBUG autolearn=ham autolearn_force=no
    version=3.4.6-bugs.debian.org_2005_01_02
    X-Spam-Bayes: score:0.0000 Tokens: new, 60; hammy, 150; neutral, 1203; spammy,
    0. spammytokens: hammytokens:0.000-+--XDebbugsCc,
    0.000-+--X-Debbugs-Cc, 0.000-+--H*M:reportbug, 0.000-+--H*MI:reportbug,
    0.000-+--H*x:12.0.0
    Return-path: <leeejobsaccount@mail.co.uk>
    Received: from 137.127.199.146.dyn.plus.net ([146.199.127.137]:47666 helo=Sprat.Spatial)
    by buxtehude.debian.org wi