Dear All,
I am facing problem in connecting to the remote router and getting error as " Cause i = 0x82C1 - Bearer capability not implemented ". Pls find the sh ver command for the hardware details and the Debug command output. As checked on internet it
seems to be issue at Telco end which is difficult to prove. From previous post got the info as The bearer capability refers to the type of call, whether it is 64k, 56k, data over voice, or voice.
There may be some others. When you place an ISDN call, the originating side specifies the type of call it is placing (bearer capability), the local CO must allow it, the far end CO must allow it,and the far end answering device must allow it. Pls help me
to find the solution.
------------- sh ver -------------------
pdal228 uptime is 1 week, 17 hours, 19 minutes
System returned to ROM by power-on
System restarted at 13:17:49 UTC Sun Jun 4 2017
System image file is "flash:c2600-is-mz.122-15.T9.bin"

cisco 2620XM (MPC860P) processor (revision 0x301) with 126976K/4096K bytes of memory.
Processor board ID JAE0823L0Q2 (4289187708)
M860 processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
Basic Rate ISDN software, Version 1.1.
1 FastEthernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
3 ISDN Basic Rate interface(s)
4 Voice NT or TE BRI interface(s)
32K bytes of non-volatile configuration memory.
49152K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102
------------- Debug output ----------
8#isdn test call int BRI0/0 19712342350
.Jun 12 04:57:40.082: ISDN BR0/0 EVENT: UserIdle: callid 0x8176 received ISDN_CALL (0x0)
.Jun 12 04:57:40.086: ISDN BR0/0 Q931: TX -> SETUP pd = 8 callref = 0x73
Bearer Capability i = 0x8890
Standard = CCITT
Transer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0x83
Keypad Facility i = '19712342350'
.Jun 12 04:57:40.258: ISDN BR0/0 Q931: RX <- CALL_PROC pd = 8 callref = 0xF3
Channel ID i = 0x89
.Jun 12 04:57:40.262: ISDN BR0/0 EVENT: process_rxstate: ces/callid 1/0x8176 calltype 1 HOST_PROCEEDING
pdal228#
.Jun 12 04:57:42.910: ISDN BR0/0 Q931: RX <- DISCONNECT pd = 8 callref = 0xF3
Cause i = 0x82C1 - Bearer capability not implemented
.Jun 12 04:57:42.914: ISDN BR0/0 EVENT: process_rxstate: ces/callid 1/0x8176 calltype 1 HOST_DISCONNECT
.Jun 12 04:57:42.918: ISDN BR0/0 Q931: TX -> RELEASE pd = 8 callref = 0x73 .Jun 12 04:57:43.006: ISDN BR0/0 Q931: RX <- RELEASE_COMP pd = 8 callref = 0xF3
.Jun 12 04:57:43.010: ISDN BR0/0 EVENT: process_rxstate: ces/callid 1/0x8176 calltype 1 HOST_DISCONNECT_ACK#
-------
Regards,
Swapnil

--- SoupGate-Win32 v1.05
* Origin: fsxNet Usenet Gateway (21:1/5)